Infiniti G35 (V35) Sedan. Manual — part 1457
WT-16
< COMPONENT DIAGNOSIS >
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
Description
INFOID:0000000000957869
A sensor-transmitter integrated with a valve is installed on a wheel, and transmits a detected air pressure sig-
nal in the from of a radio wave.
DTC Logic
INFOID:0000000000957870
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK ID REGISTRATION AND VEHICLE DRIVING
With CONSULT-III
1.
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
2.
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.
Does “DATA MONITOR” displayed the standardized value without turning tire pressure warning lamp ON?
YES
>> INSPECTION END
NO
>> Go to diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000000957871
1.
CHECK AIR PRESSURE SIGNAL
With CONSULT-III
1.
Start engine
2.
Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.
3.
Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, “AIR PRESS RL”.
Are all tire pressures displayed 0 kPa?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER
1.
Turn ignition switch “OFF”.
DTC number
Trouble diagnosis
name
DTC detecting condition
Possible cause
C1708
[NO DATA] FL
Data from front-left transmitter can not received.
• Harness or connector
(Tire pressure receiver, BCM)
• ID registration is not finished
• Transmitter malfunction
C1709
[NO DATA] FR
Data from front-right transmitter can not received.
C1710
[NO DATA] RR
Data from rear-right transmitter can not received.
C1711
[NO DATA] RL
Data from rear-left transmitter can not received.
Monitored item
Condition
Display value
AIR PRESS FL
Start engine and drive at 40 km/h (25 MPH) or more for
several minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Monitored item
Condition
Display value
AIR PRESS FL
Start engine and drive at 40 km/h (25 MPH) or more for several
minutes.
Approximately equal to the indication on
vehicle information display
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
WT-17
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
2.
Disconnect BCM harness connector and tire pressure receiver harness connector.
3.
Check continuity between BCM harness connector and tire pressure receiver harness connector.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER
Check tire pressure receiver. Refer to
.
Is the inspection result normal?
YES
>> Check BCM pin terminals for damage or loose connection with harness connector. If any items
are damaged, repair or replace damage parts.
NO
>> Replace the tire pressure receiver.
4.
CHECK ID REGISTRATION
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair
Can ID registration of all transmitters be completed?
YES
>> GO TO 5.
NO
>> Replace malfunctioning transmitter, then GO TO 6.
5.
CHECK TIRE PRESSURE MONITORING SYSTEM
With CONSULT-III
1.
Drive at a speed 40 km/h (25 MPH) or more for several minutes without stopping.
2.
Check all tire pressures with CONSULT-III “DATA MONITOR” within 15 minutes after vehicle speed
becomes 17 km/h (11 MPH).
Does “DATA MONITOR” displayed the standardized value without turning tire pressure warning lamp ON?
YES
>> INSPECTION END
NO
>> Replace BCM. Refer to
BCS-79, "Removal and Installation"
6.
CHECK ID REGISTRATION
With CONSULT-III
1.
Perform ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
2.
Drive at a speed 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10
minutes. Then check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes.
Does “DATA MONITOR” displayed the standardized value without turning tire pressure warning lamp ON?
YES
>> INSPECTION END
NO
>> Perform the self-diagnosis, inspect detected malfunction.
Special Repair Requirement
INFOID:0000000000957872
1.
CHECK TIRE AIR PRESSURE
Check all tire air pressures. Refer to
Does all tire pressure data meet the specification?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.
2.
PERFORM ID REGISTRATION
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M101
1
Existed
138
4
139
2
WT-18
< COMPONENT DIAGNOSIS >
C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)
Perform ID registration. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"
.
Can ID registration of all transmitters be completed?
YES
>> END
NO
>> GO TO 1.
C1712, C1713, C1714, C1715 TRANSMITTER (CHECKSUM)
WT-19
< COMPONENT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
C1712, C1713, C1714, C1715 TRANSMITTER (CHECKSUM)
Description
INFOID:0000000000957873
A sensor-transmitter integrated with a valve is installed on a wheel, and transmits a detected air pressure sig-
nal in the from of a radio wave.
DTC Logic
INFOID:0000000000957874
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
VEHICLE DRIVING
With CONSULT-III
1.
Driving at a speed 40 km/h (25 MPH) or more for 3 minutes, and then driving the vehicle at any speed for
10 minutes.
2.
Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.
Does “DATA MONITOR” displayed the standardized value without turning tire pressure warning lamp ON?
YES
>> INSPECTION END
NO
>> Go to diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000000957875
1.
CHECK ID REGISTRATION
With CONSULT-III
1.
Perform the ID registration of all transmitters. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
2.
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes. Then check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.
Can ID registration of all transmitters be completed?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK AIR PRESSURE SIGNAL
With CONSULT-III
1.
Start engine.
2.
Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.
3.
Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.
DTC
Trouble diagnosis name
DTC detecting condition
Possible case
C1712
[CHECKSUM ERR] FL
Checksum data from front-left transmitter is malfunction.
• Tire pressure receiver malfunc-
tion
• Transmitter malfunction
• BCM malfunction
C1713
[CHECKSUM ERR] FR
Checksum data from front-right transmitter is malfunction.
C1714
[CHECKSUM ERR] RR
Checksum data from rear-right transmitter is malfunction.
C1715
[CHECKSUM ERR] RL
Checksum data from rear-left transmitter is malfunction.
Monitored item
Condition
Display value
AIR PRESS FL
Start engine and drive at 40 km/h (25 MPH) or more for
several minutes.
Approximately equal to the indication on vehicle
information display.
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст