Infiniti G35 (V35) Sedan. Manual — part 1270
ST-30
< ON-VEHICLE REPAIR >
STEERING GEAR AND LINKAGE
8.
Adjust pinion rotating torque with the following procedure.
a.
Measure pinion rotating torque within
±
180
°
of neutral position
of the rack assembly using Tools. Stop the gear at the point
where highest torque is read.
b.
Loosen adjusting screw and retighten to 5.4 N·m (0.55 kg-m, 48
in-lb), and then loosen by 20 to 40
°
.
c.
Measure pinion rotating torque using Tools to make sure that the
measured value is within the standard. Readjust if the value is
outside the standard. Replace steering gear assembly if the
value is outside the standard after readjusting or adjusting screw
rotating torque is 5 N·m (0.51 kg-m, 44 in-lb) or less.
d.
Apply recommended liquid gasket to inner socket and turn pinion fully to left with inner socket installed to
gear housing assembly.
e.
Install dial gauge at 5 mm (0.20 in) (L) from the edge of gear
housing assembly (1), and tooth point.
f.
Measure vertical movement of rack assembly when pinion is
turned clockwise with torque of 19.6 N·m (2.0 kg-m, 14 ft-lb).
Readjust adjusting screw angle if the measured value is outside
the standard.
• If reading is outside of the specification, readjust screw angle
with adjusting screw.
CAUTION:
• If reading is still out side of specification, or if the rotating torque of adjusting screw is less
than 5 N·m (0.51 kg-m, 44 in-lb), replace steering gear assembly.
• Never turn adjusting screw more than twice.
• Replace steering gear assembly when adjusting screw is removed or more than twice.
9.
Install large end of boot to gear housing assembly.
10. Install small end of boot to inner socket boot mounting groove.
11. Install boot clamp to boot small end.
12. Install boot clamp to the large side of boot with the following procedure.
CAUTION:
Never reuse boot clamp.
A: Preload gauge [SST: ST3127S000 (J-25765-A)]
B: Preload adapter [SST: KV48103400 (
—
)]
SGIA1383E
Pinion rotating torque
Around neutral position
(within
±
100
°
) average “A”
: 1.95 – 2.58 N·m (0.20 –
0.26 kg-m, 18 – 22 in-lb)
Maximum variation “B”
: 0.98 N·m (0.10 kg-m, 9.0
in-lb)
Vertical movement
: 0.265 mm (0.0104 in)
SGIA0936E
JSGIA0104ZZ
SGIA1325E
STEERING GEAR AND LINKAGE
ST-31
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
a.
Tighten large side of boot with boot clamp (stainless wire).
b.
Wrap clamp around boot groove for two turns. Insert a flat-
bladed screwdriver in loops on both ends of wire. Twist 4 to 4.5
turns while pulling them with force of approximately 98 N (10 kg,
22 lb).
c.
Twist boot clamp as shown. Pay attention to relationship
between winding and twisting directions.
d.
Twisted area (A) of clamp is in the opposite side of adjusting
screw (1) as shown in the figure (to prevent contact with other
parts).
e.
Bent cut end of the wire as shown in the figure after twisting the
wire 4 to 4.5 turns so that cut end does not contact with boot.
CAUTION:
Keep gap from cylinder tube 5 mm (0.20 in) or more.
13. Install cylinder tubes to gear housing assembly.
14. Install low pressure piping.
Wire length “L”
: 370 mm (14.57 in)
SGIA0163E
SGIA0164E
JSGIA0101ZZ
Wire angle “A”
: 45
°
JSGIA0102ZZ
ST-32
< ON-VEHICLE REPAIR >
STEERING GEAR AND LINKAGE
15. Adjust inner socket to standard length “L”, and then tighten lock
nut to the specified torque. Check length “L” again after tighten-
ing lock nut.
CAUTION:
Adjust toe-in after this procedure. Length achieved after
toe-in adjustment is not necessary the above value.
2WD : Inspection
INFOID:0000000000958677
INSPECTION AFTER INSTALLATION
• Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check the fluid level, fluid leakage, and air bleeding hydraulic system. Refer to
.
• Perform 4WAS front actuator neutral position adjustment. Refer to
NEUTRAL POSITION ADJUSTMENT : Description"
INSPECTION AFTER DISASSEMBLY
Boot
• Check boot for cracks, and replace it if a malfunction is detected.
Rack Assembly
• Check rack for damage or wear, and replace it if a malfunction is detected.
Gear-Sub Assembly
• Check gear-sub assembly for damage or wear, and replace it if a malfunction is detected.
• Rotate gear-sub assembly and check for torque variation or rattle, and replace it if a malfunction is detected.
Gear Housing Assembly
• Check gear housing assembly for damage and scratches (inner wall). Replace if there are.
Outer Socket and Inner Socket
• Check the following items and replace the component if it does not meet the standard.
BALL JOINT SWINGING TORQUE
• Hook a spring balance at the point shown in the figure and pull the
spring balance. Make sure that the spring balance reads the spec-
ified value when ball stud and inner socket start to move. Replace
outer socket and inner socket if they are outside the standard.
BALL JOINT ROTATING TORQUE
Standard
Inner socket length “L”
: Refer to
.
SGIA0167E
Standard for outer socket
(Measuring point: Stud cotter pin mounting hole)
Spring balance measure-
ment
Swing Force and Rotating
Torque"
Standard for inner socket
(Measuring point: “*” mark shown in the figure)
Spring balance measure-
ment
Swing Force and Rotating
Torque"
SGIA0896E
STEERING GEAR AND LINKAGE
ST-33
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Make sure that the reading is within the following specified range
using preload gauge (A) [SST: ST3127S000 (J-25765-A)]. Replace
outer socket if the reading is outside the specified value.
BALL JOINT AXIAL END PLAY
• Apply an axial load of 490 N (50 kg, 110 lb) to ball stud. Using a
dial gauge, measure amount of stud movement, and then make
sure that the value is within the following specified range. Replace
outer socket (1) and inner socket (2) if the measured value is out-
side the standard.
AWD
AWD : Exploded View
INFOID:0000000000958678
REMOVAL AND INSTALLATION
DISASSEMBLY AND ASSEMBLY
Standard
Outer socket rotating
torque
: Refer to
Swing Force and Rotating
Torque"
SGIA1382E
Standard
Outer socket
: Refer to
Inner socket
: Refer to
JSGIA0109ZZ
1.
Steering gear assembly
2.
cotter pin
: Vehicle front
Refer to
JSGIA0039GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст