Infiniti G35 (V35) Sedan. Manual — part 907
LU-12
< ON-VEHICLE REPAIR >
OIL FILTER BRACKET
ON-VEHICLE REPAIR
OIL FILTER BRACKET
AWD
AWD : Exploded View
INFOID:0000000000956315
AWD : Removal and Installation
INFOID:0000000000956316
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil may be hot.
1.
Remove engine undercover with power tool.
2.
Using the oil filter wrench [SST: KV10115801 (J38956)], remove oil filter. Refer to
.
CAUTION:
Do not spill engine oil on drive belt.
3.
Remove connector bolt, and then oil cooler with water hoses connected.
4.
Disconnect oil pressure switch harness connector and oil temperature sensor harness connector.
5.
Remove oil filter bracket from oil pan (upper).
6.
Remove oil pressure switch and oil temperature sensor from oil filter bracket.
1.
Oil pan (upper)
2.
Gasket
3.
Relief valve
4.
Washer
5.
Oil temperature sensor
6.
Oil pressure switch
7.
Oil filter bracket
8.
O-ring
9.
Oil cooler
10.
Connector bolt
11.
Oil filter
A.
Refer to
B.
: Engine front
Refer to
for symbol marks in the figure.
JPBIA0245GB
OIL FILTER BRACKET
LU-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
INSTALLATION
• Install oil pressure switch as follows:
- Remove old liquid gasket adhering to oil filter bracket.
- Apply liquid gasket and install oil pressure switch.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products
• Align cutout on oil cooler with protrusion on oil filter bracket. Refer to
AWD : Inspection
INFOID:0000000000956317
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and add engine oil. Refer to
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
LU-14
< ON-VEHICLE REPAIR >
OIL COOLER
OIL COOLER
AWD
AWD : Exploded View
INFOID:0000000000956318
AWD : Removal and Installation
INFOID:0000000000956319
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
NOTE:
When removing oil cooler only, step 2 is unnecessary.
1.
Remove engine undercover with power tool.
2.
Drain engine coolant from radiator and cylinder block. Refer to
.
NOTE:
Perform this step when removing water pipes.
3.
Disconnect water hoses from oil cooler.
1.
Oil filter bracket
2.
Relief valve
3.
O-ring
4.
Gasket
5.
Oil cooler
6.
Clamp
7.
Water hose
8.
Water hose
9.
Connector bolt
10.
Oil filter
11.
Water pipe
12.
Water hose
13.
Water hose
14.
Water pipe
15.
Heater pipe
: Engine front
for symbol marks in the figure.
JPBIA0244GB
OIL COOLER
LU-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
• When removing oil cooler only, pinching water hoses near oil cooler to prevent engine coolant from spill-
ing out.
• Remaining engine coolant in piping will come out. Use a tray to collect it.
CAUTION:
• Perform this step when the engine is cold.
• Do not spill engine coolant on drive belts.
4.
Using oil filter wrench [SST: KV10115801 (J38956)], remove oil filter. Refer to
.
CAUTION:
Do not spill engine oil on drive belts.
5.
Remove connector bolt, and remove oil cooler.
CAUTION:
Do not spill engine oil to rubber parts such as drive belts and engine mounting insulator.
6.
Remove water pipes, as necessary.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Make sure that no foreign objects are adhering to the installation planes of oil filter and oil cooler bracket.
• Align cutout on oil cooler with protrusion on oil filter bracket side, and tighten connector bolt.
AWD : Inspection
INFOID:0000000000956320
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.
Relief Valve
Check relief valve with the following procedure.
• Press steel ball of relief valve using a clean plastic stick. Make sure that valve moves smoothly and proper
spring repulsion is felt.
• Replace relief valve, if necessary, with the following procedure.
- Remove the relief valve by prying using a screwdriver.
CAUTION:
Be careful not to damage the mounting hole.
- Press in the relief valve until it reaches a depth of 7 mm (0.28 in) from end surface of oil pan (upper) using
approximately 10 mm (0.39 in) diameter drift.
CAUTION:
Carefully press in the relief valve by aligning its mounting hole side with the axle center so as not to
cause deformation.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
.
2.
Start the engine, and check there is no leaks of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
and
1
: Oil cooler
2
: Oil filter bracket
3
: Connector bolt
A
: Protrusion
B
: Cut out
: Engine front
JPBIA0083ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст