Infiniti G35 (V35) Sedan. Manual — part 1266
ST-14
< ON-VEHICLE MAINTENANCE >
STEERING WHEEL
4.
With the engine at idle, turn steering wheel from full left stop to
full right stop and measure the turning angles.
5.
Check the following items when turning angle is out of the stan-
dard.
a.
Check rack stroke.
b.
Disassemble steering gear assembly to check the cause that
rack stroke is outside of the standard.
• Steering angles are not adjustable. Check steering gear
assembly, steering column assembly and front suspension
components for wear or damage if any of the turning angles are different from the specified value.
Replace any of them, if any non-standard condition exists.
Standard
Inner wheel (Angle: A)
: Refer to
.
Outer wheel (Angle: B)
: Refer to
.
SGIA0055E
Standard
Rack stroke “L”
: Refer to
.
SGIA0629J
STEERING WHEEL
ST-15
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
ON-VEHICLE REPAIR
STEERING WHEEL
Exploded View
INFOID:0000000000958659
Removal and Installation
INFOID:0000000000958660
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1.
Set vehicle to the straight-ahead position.
2.
Remove driver air bag module. Refer to
SR-4, "Removal and Installation"
3.
Remove steering wheel lock nut after steering is locked.
4.
Remove steering wheel with the steering wheel puller (A) [SST:
ST27180001 (J-25726-A)].
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never twist spiral cable freely on excessively after it becomes tight (doing so may cause the cable to
be turn off).
NOTE:
Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to
1.
Steering wheel
Refer to
JSGIA0026GB
SGIA1323E
ST-16
< ON-VEHICLE REPAIR >
STEERING COLUMN
STEERING COLUMN
MANUAL TYPE
MANUAL TYPE : Exploded View
INFOID:0000000000958661
MANUAL TYPE : Removal and Installation
INFOID:0000000000958662
REMOVAL
1.
Set vehicle to the straight-ahead position.
2.
Place the tilt to the highest level. Place the telescopic to the longest level.
3.
Remove driver air bag module. Refer to
SR-4, "Removal and Installation"
4.
Remove steering wheel. Refer to
.
5.
Remove steering column cover. Refer to
IP-12, "Removal and Installation"
6.
Remove spiral cable. Refer to
SR-7, "Removal and Installation"
.
7.
Remove combination switch. Refer to
MWI-156, "Removal and Installation"
8.
Remove instrument driver lower panel. Refer to
IP-12, "Removal and Installation"
.
9.
Remove knee protector (1).
10. Remove combination meter. Refer to
.
11. Disconnect each switch harness connectors installed to steering
column assembly.
12. Remove the joint mounting bolt and nut (lower shaft side), and
separate the joint from lower shaft.
13. Remove steering column assembly.
CAUTION:
• Never give axial impact to steering column assembly dur-
ing removal.
• Never move steering gear assembly when removing steering column assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Be careful of the following points when installing the steering column assembly.
CAUTION:
1.
Steering column assembly
Refer to
for symbols in the figure.
JSGIA0028GB
JSGIA0030ZZ
STEERING COLUMN
ST-17
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Never give axial impact to steering column assembly during installation.
• Never move steering gear assembly.
• Never reuse the joint mounting nut (lower shaft side).
• Adjust neutral position of steering angle sensor. Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
MANUAL TYPE : Inspection
INFOID:0000000000958663
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are.
• Measure steering column assembly rotating torque using a preload gauge [SST: ST3127S000 (J-25765-A)].
Replace steering column assembly if outside the standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
• Check tilt and telescopic mechanism operating range “L”, “T” as
shown in the figure.
AUTOMATIC
AUTOMATIC : Exploded View
INFOID:0000000000958664
Standard
Rotating torque
: Refer to
Standard
Tilt operating range “T”
: Refer to
Telescopic operating
range “L”
: Refer to
JSGIA0033ZZ
1.
Upper stay
2.
Clip
3.
Steering column assembly
4.
Clip
JSGIA0029GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст