Infiniti G35 (V35) Sedan. Manual — part 913
ENGINE MAINTENANCE
MA-17
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
2.
Using oil filter wrench [SST: KV10115801 (J38956)] (B), remove
oil filter.
INSTALLATION
1.
Remove foreign materials adhering to oil filter installation surface.
2.
Apply engine oil to the oil seal contact surface of new oil filter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to the specification.
OIL FILTER : Inspection
INFOID:0000000000967312
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
A
: 2WD
: Engine front
JPBIA0252GB
A
: AWD
: Engine front
JPBIA0076ZZ
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
MA-18
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000000967313
REMOVAL
1.
Remove engine cover with power tool. Refer to
.
2.
Remove air cleaner case and air duct (RH and LH). Refer to
.
3.
Remove electric throttle control actuator. Refer to
.
4.
Remove ignition coil. Refer to
EM-45, "Removal and Installation"
.
5.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
INSTALLATION
Installation is the reverse order of removal.
SPARK PLUG : Inspection
INFOID:0000000000967314
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
• Do not drop or shock spark plug.
• Do not use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
change intervals.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000000967315
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
Cleaner air pressure:
Less than 588 kPa (6 kg/
cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
JPBIA0031ZZ
ENGINE MAINTENANCE
MA-19
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1.
Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration.
2.
Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc.
Refer to
MA-20
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
CHASSIS MAINTENANCE
EXHAUST SYSTEM
EXHAUST SYSTEM : Inspection
INFOID:0000000000967316
Check exhaust pipes, muffler and mounting for improper attachment,
leaks, cracks, damage, chafing or deterioration.
• If anything is found, repair or replace damaged parts.
A/T FLUID
A/T FLUID : Inspection
INFOID:0000000000967317
A/T FLUID LEAKAGE AND A/T FLUID LEVEL CHECK
1.
Warm up engine.
2.
Check for A/T fluid leakage.
3.
Loosen the level gauge bolt.
4.
Before driving, A/T fluid level can be checked at A/T fluid tem-
peratures of 30 to 50
°
C (86 to 122
°
F) using “COLD” range on A/
T fluid level gauge as follows.
a.
Park vehicle on level surface and set parking brake.
b.
Start engine and move selector lever through each gear posi-
tion. Leave selector lever in “P” position.
c.
Check A/T fluid level with engine idling.
d.
Remove A/T fluid level gauge and wipe clean with lint-free
paper.
CAUTION:
When wiping away the A/T fluid level gauge, always use
lint-free paper, not a cloth one.
e.
Re-insert A/T fluid level gauge into A/T fluid charging pipe as far as it will go.
CAUTION:
To check A/T fluid level, insert the A/T fluid level gauge until the cap contacts the end of the A/T
fluid charging pipe, with the A/T fluid level gauge reversed from the normal attachment conditions.
f.
Remove A/T fluid level gauge and note reading. If reading is at low side of range, add ATF to the A/T fluid
charging pipe.
CAUTION:
Do not overfill.
5.
Drive vehicle for approximately 5 minutes in urban areas.
6.
Make the A/T fluid temperature approximately 65
°
C (149
°
F).
NOTE:
SMA211A
SCIA7120E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст