Infiniti I30 (A33). Manual — part 138
LAN SIGNAL 3 — Continued Reception After
LAN Communication Starts
=NHBR0087
DIAGNOSTIC PROCEDURE
NHBR0087S01
Malfunction code No. 94
1
INSPECTION START
Self-diagnostic item “LAN SIGNAL 3” appears on display.
SBR541E
©
GO TO 2.
2
CHECK SELF-DIAGNOSIS
Perform self-diagnostic procedures for ECM.
Does self-diagnostic item [ECM-ABSTCS COMM NG] appear on display?
Yes
©
Check ECM. Refer to “TROUBLE DIAGNOSES” in EC section.
No
©
GO TO 3.
3
CHECK SELF-DIAGNOSIS
Does self-diagnostic item [ABS-TCS C/U SIGNAL] appears on display?
Yes
©
I
Replace control unit.
I
Repeat self-diagnostic procedures for control unit.
No
©
If other items appears on display, repair or replace affected areas.
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSES FOR SELF-DIAGNOSTIC ITEMS
TCS
LAN SIGNAL 3 — Continued Reception After LAN Communication Starts
BR-135
1. ABS Works Frequently
NHBR0073
1
CHECK BRAKE FLUID PRESSURE
Check brake fluid pressure distribution.
Refer to dual proportioning valve inspection in “DUAL PROPORTIONING VALVE”, BR-12.
Is brake fluid pressure distribution normal?
Yes
©
GO TO 2.
No
©
Perform Preliminary Check. Refer to BR-101.
2
CHECK WHEEL SENSOR
1. Check wheel sensor connector for terminal damage or loose connections.
2. Perform wheel sensor mechanical check.
Refer to “Wheel Sensor or Rotor”, BR-107.
Are wheel sensors functioning properly?
Yes
©
GO TO 3.
No
©
Repair.
3
CHECK FRONT AXLE
Check front and rear axles for excessive looseness. Refer to AX section, “Front Wheel Bearing”, “ON-VEHICLE SERVICE”
and “Rear Wheel Bearing”, “ON-VEHICLE SERVICE”.
Is front axle installed properly?
Yes
©
Go to “3. CHECK WARNING LAMP INDICATION” in “2. Unexpected Pedal Action”,
BR-136.
No
©
Repair.
2. Unexpected Pedal Action
NHBR0071
1
CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Is stroke excessively large?
SBR540A
Yes
©
Perform Preliminary Check. Refer to BR-101.
No
©
GO TO 2.
TROUBLE DIAGNOSES FOR SYMPTOMS
TCS
1. ABS Works Frequently
BR-136
2
CHECK CONNECTOR AND PERFORMANCE
1. Disconnect ABS solenoid valve relay.
2. Check whether brake is effective.
OK or NG
Yes
©
GO TO 3.
No
©
Perform Preliminary Check. Refer to BR-101.
3
CHECK WARNING LAMP INDICATION
Ensure warning lamp remains off while driving.
SBR655E
Is warning lamp turned off?
Yes
©
GO TO 4.
No
©
Carry out self-diagnosis. Refer to BR-91, BR-94.
4
CHECK WHEEL SENSOR
1. Check wheel sensor connector for terminal damage or loose connection.
2. Perform wheel sensor mechanical check. Refer to “Wheel Sensor Rotor”, BR-107.
Is wheel sensor mechanism OK?
Yes
©
Check control unit pin terminals for damage or the connection of control unit harness
connector. Reconnect control unit harness connector. Then retest.
No
©
Repair.
3. Long Stopping Distance
NHBR0070
1
CHECK CONNECTOR AND PERFORMANCE
1. Cancel ABS by disconnecting ABS solenoid valve relay.
2. Check stopping distance.
OK or NG
OK
©
Perform Preliminary Check and air bleeding.
NG
©
Go to “3. CHECK WARNING LAMP INDICATION” in “2. Unexpected Pedal Action”,
BR-136.
GI
MA
EM
LC
EC
FE
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSES FOR SYMPTOMS
TCS
2. Unexpected Pedal Action (Cont’d)
BR-137
NOTE:
Stopping distance may be longer than vehicles without ABS when
road condition is slippery.
4. ABS Does Not Work
NHBR0072
1
CHECK WARNING LAMP INDICATION
Does the ABS warning lamp activate?
Yes
©
Carry out self-diagnosis. Refer to BR-91, 94.
No
©
Go to “3. CHECK WARNING LAMP INDICATION” in “2. Unexpected Pedal Action”,
BR-136.
NOTE:
ABS does not work when vehicle speed is under 10 km/h (6 MPH).
TROUBLE DIAGNOSES FOR SYMPTOMS
TCS
3. Long Stopping Distance (Cont’d)
BR-138
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст