Infiniti I30 (A33). Manual — part 355
SEL972X
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
PARKING, LICENSE AND TAIL LAMPS
Wiring Diagram — TAIL/L — (Cont’d)
EL-89
SEF289X
CONSULT-II Inspection Procedure
NHEL0209
“RETAINED PWR”
NHEL0209S01
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” to the data link connector.
PBR455D
3.
Turn ignition switch “ON”.
4.
Touch “START”.
SEL941W
5.
Touch “SMART ENTRANCE”.
SEL273W
6.
Touch “RETAINED PWR”.
SEL322W
7.
Select diagnosis mode.
“DATA MONITOR” and “ACTIVE TEST” are available.
PARKING, LICENSE AND TAIL LAMPS
CONSULT-II Inspection Procedure
EL-90
CONSULT-II Application Items
NHEL0210
“RETAINED PWR”
NHEL0210S01
Data Monitor
NHEL0210S0101
Monitored Item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
Active Test
NHEL0210S0102
Test Item
Description
RETAINED PWR
This test is able to supply RAP signal (power) from smart entrance control unit to power window
system, power sunroof system and headlamp system. Those systems can be operated when turn-
ing on “RETAINED PWR” on CONSULT-II screen even if the ignition switch is tuned OFF.
NOTE:
During this test, CONSULT-II can be operated with ignition switch “OFF” position.
“RETAINED PWR” should be turned “ON” or “OFF” on CONSULT-II screen when ignition
switch is ON. Then turn ignition switch OFF for checking retained power operation. CON-
SULT-II might be stuck if “RETAINED PWR” is turned “ON” or “OFF” on CONSULT-II screen
when ignition switch is OFF.
Trouble Diagnoses
NHEL0211
Symptom
Possible cause
Repair order
No lamps operate (including head-
lamps).
1. 10A fuse
2. Lighting switch
3. Smart entrance control unit
1. Check 10A fuse [No. 13, lacated in fuse block (J/B)].
Verify battery positive voltage is present at terminal
49 of smart entrance control unit.
2. Check lighting switch.
3. Check smart entrance control unit. (EL-406)
No parking, side marker, license
and tail lamps operate, but head-
lamps do operate.
1. 10A fuse
2. Tail lamp relay
3. Tail lamp relay circuit
4. Lighting switch
5. Lighting switch circuit
6. Smart entrance control unit
1. Check 10A fuse (No. 60, located in fusible and fuse
block). Verify battery positive voltage is present at
terminals 1 and 3 of tail lamp relay.
2. Check tail lamp relay.
3. Check harness between smart entrance control unit
terminals 19 and 57 and tail lamp relay terminal 2.
Check harness between tail lamp relay terminal 5 and
ground.
4. Check lighting switch.
5. Check harness between lighting switch terminal 11
and smart entrance control unit terminals 20 and 58.
Check harness between lighting switch terminal 5 and
ground.
6. Check smart entrance control unit. (EL-406)
Battery saver control does not
operate properly.
1. Smart entrance control unit
1. Check smart entrance control unit. (EL-406)
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
PARKING, LICENSE AND TAIL LAMPS
CONSULT-II Application Items
EL-91
Wiring Diagram — STOP/L —
NHEL0025
MEL408M
STOP LAMP
Wiring Diagram — STOP/L —
EL-92
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст