Infiniti I30 (A33). Manual — part 326
Wiring Diagram
NHEC0396
MEC935C
SEF639XB
GI
MA
EM
LC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FUEL PUMP
Wiring Diagram
EC-619
Diagnostic Procedure
NHEC0397
1
CHECK OVERALL FUNCTION
1. Turn ignition switch “ON”.
2. Pinch fuel feed hose with two fingers.
SEC013C
Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned “ON”.
OK or NG
OK
©
INSPECTION END
NG
©
GO TO 2.
2
CHECK FUEL PUMP RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch “OFF”.
2. Disconnect fuel pump relay.
SEF284X
3. Turn ignition switch “ON”.
4. Check voltage between terminals 1, 5 and ground with CONSULT-II or tester.
SEF898X
OK or NG
OK
©
GO TO 4.
NG
©
GO TO 3.
FUEL PUMP
Diagnostic Procedure
EC-620
3
DETECT MALFUNCTIONING PART
Check the following.
I
Fuse block (J/B) connector B5
I
10A fuse
I
15A fuse
I
Harness for open or short between fuse and fuel pump relay
©
Repair harness or connectors.
4
CHECK FUEL PUMP POWER SUPPLY AND GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch “OFF”.
2. Disconnect fuel level sensor unit and fuel pump harness connector.
SEF263X
3. Check harness continuity between fuel pump terminal 3 and body ground, fuel pump terminal 1 and fuel pump relay
terminal 3. Refer to Wiring Diagram.
Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 6.
NG
©
GO TO 5.
5
DETECT MALFUNCTIONING PART
Check the following.
I
Harness for open or short between fuel pump relay and fuel pump
I
Harness for open or short between fuel pump and body ground
©
Repair open circuit or short to ground or short to power in harness or connectors.
6
CHECK FUEL PUMP RELAY OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect ECM harness connector.
2. Check harness continuity between ECM terminal 28 and fuel pump relay terminal 2. Refer to Wiring Diagram.
Continuity should exist.
3. Also check harness for short to ground and short to power.
OK or NG
OK
©
GO TO 8.
NG
©
GO TO 7.
7
DETECT MALFUNCTIONING PART
Check the following.
I
Harness connectors B3, M6
I
Harness connectors M81, F49
I
Harness for open or short between ECM and fuel pump relay
©
Repair open circuit or short to ground or short to power in harness or connectors.
GI
MA
EM
LC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FUEL PUMP
Diagnostic Procedure (Cont’d)
EC-621
8
CHECK FUEL PUMP RELAY
With CONSULT-II
1. Reconnect fuel pump relay, fuel level sensor unit and fuel pump harness connector and ECM harness connector.
2. Turn ignition switch “ON”.
3. Turn fuel pump relay “ON” and “OFF” in “ACTIVE TEST” mode with CONSULT-II and check operating sound.
SEF073Y
Without CONSULT-II
Check continuity between terminals 3 and 5 under the following conditions.
SEF608X
OK or NG
OK
©
GO TO 9.
NG
©
Replace fuel pump relay.
9
CHECK FUEL PUMP
1. Disconnect fuel level sensor unit and fuel pump harness connector.
2. Check resistance between fuel level sensor unit and fuel pump terminals 1 and 3.
SEF609X
OK or NG
OK
©
GO TO 10.
NG
©
Replace fuel pump.
FUEL PUMP
Diagnostic Procedure (Cont’d)
EC-622
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст