Infiniti I30 (A33). Manual — part 509
SGI986
SGI987
Tow Truck Towing
NHGI0009S05
CAUTION:
I
All applicable state or Provincial (in Canada) laws and
local laws regarding the towing operation must be
obeyed.
I
It is necessary to use proper towing equipment to avoid
possible damage to the vehicle during towing operation.
Towing is in accordance with Towing Procedure Manual at
dealer.
I
Always attach safety chains before towing.
I
When towing, make sure that the transmission, steering
system and power train are in good order. If any unit is
damaged, dollies must be used.
INFINITI recommends that the vehicle be towed with the driving
(front) wheels off the ground as illustrated.
CAUTION:
I
Always release the parking brake when towing the vehicle
with the front wheels raised with the rear wheels on the
ground.
I
When towing manual transaxle models with the front
wheels on the ground (If a towing dollies does not be
used), turn the ignition key to the OFF position, and
secure the steering wheel in the straight-ahead position
with a rope or similar device. Never place the ignition key
in the LOCK position. This will result in damage to the
steering lock mechanism.
Move the shift lever to the N (Neutral) position.
I
Never tow an automatic transaxle model with the rear
wheels raised and the front wheels on the ground. This
may cause serious and expensive damage to the tran-
saxle. If it is necessary to tow the vehicle with the rear
wheels raised, always use towing dollies under the front
wheels.
I
Never tow an automatic transaxle model from the rear
(that is backward) with four wheels on the ground. This
may cause serious and expensive damage to the tran-
saxle.
VEHICLE RECOVERY (FREEING A STUCK VEHICLE)
NHGI0009S0501
I
Tow chains or cables must be attached only to the main
structural members of the vehicle.
I
Pulling devices should be routed so they do not touch any
part of the suspension, steering, brake or cooling sys-
tems.
I
Always pull the cable straight out from the front or rear of
the vehicle. Never pull on the vehicle at an angle.
I
Pulling devices such as ropes or canvas straps are not
recommended for use in vehicle towing or recovery.
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
LIFTING POINTS AND TOW TRUCK TOWING
Tow Truck Towing
GI-49
NHGI0010
Grade
Bolt size
Bolt diam-
eter *
mm
Pitch
mm
Tightening torque (Without lubricant)
Hexagon head bolt
Hexagon flange bolt
N·m
kg-m
ft-lb
in-lb
N·m
kg-m
ft-lb
in-lb
4T
M6
6.0
1.0
5.1
0.52
3.8
45.1
6.1
0.62
4.5
53.8
M8
8.0
1.25
13
1.3
9
—
15
1.5
11
—
1.0
13
1.3
9
—
16
1.6
12
—
M10
10.0
1.5
25
2.5
18
—
29
3.0
22
—
1.25
25
2.6
19
—
30
3.1
22
—
M12
12.0
1.75
42
4.3
31
—
51
5.2
38
—
1.25
46
4.7
34
—
56
5.7
41
—
M14
14.0
1.5
74
7.5
54
—
88
9.0
65
—
7T
M6
6.0
1.0
8.4
0.86
6.2
74.6
10
1.0
7
87
M8
8.0
1.25
21
2.1
15
—
25
2.5
18
—
1.0
22
2.2
16
—
26
2.7
20
—
M10
10.0
1.5
41
4.2
30
—
48
4.9
35
—
1.25
43
4.4
32
—
51
5.2
38
—
M12
12.0
1.75
71
7.2
52
—
84
8.6
62
—
1.25
77
7.9
57
—
92
9.4
68
—
M14
14.0
1.5
127
13.0
94
—
147
15.0
108
—
9T
M6
6.0
1.0
12
1.2
9
—
15
1.5
11
—
M8
8.0
1.25
29
3.0
22
—
35
3.6
26
—
1.0
31
3.2
23
—
37
3.8
27
—
M10
10.0
1.5
59
6.0
43
—
70
7.1
51
—
1.25
62
6.3
46
—
74
7.5
54
—
M12
12.0
1.75
98
10.0
72
—
118
12.0
87
—
1.25
108
11.0
80
—
137
14.0
101
—
M14
14.0
1.5
177
18.0
130
—
206
21.0
152
—
*: Nominal diameter
1)
Special parts are excluded.
2)
This standard is applicable to bolts having the following marks embossed on the bolt head.
MGI044A
TIGHTENING TORQUE OF STANDARD BOLTS
GI-50
NHGI0011
SAE J1930 Terminology List
NHGI0011S01
All emission related terms used in this publication in accordance with SAE J1930 are listed. Accordingly, new
terms, new acronyms/abbreviations and old terms are listed in the following chart.
***: Not applicable
NEW TERM
NEW ACRONYM /
ABBREVIATION
OLD TERM
Air cleaner
ACL
Air cleaner
Barometric pressure sensor
BARO sensor
***
Barometric pressure sensor-BCDD
BAROS-BCDD
BCDD
Camshaft position
CMP
***
Camshaft position sensor
CMPS
Crank angle sensor
Canister
***
Canister
Carburetor
CARB
Carburetor
Charge air cooler
CAC
Intercooler
Closed loop
CL
Closed loop
Closed throttle position switch
CTP switch
Idle switch
Clutch pedal position switch
CPP switch
Clutch switch
Continuous fuel injection system
CFI system
***
Continuous trap oxidizer system
CTOX system
***
Crankshaft position
CKP
***
Crankshaft position sensor
CKPS
***
Data link connector
DLC
***
Diagnostic test mode
DTM
Diagnostic mode
Diagnostic test mode selector
DTM selector
Diagnostic mode selector
Diagnostic test mode I
DTM I
Mode I
Diagnostic test mode II
DTM II
Mode II
Diagnostic trouble code
DTC
Malfunction code
Direct fuel injection system
DFI system
***
Distributor ignition system
DI system
Ignition timing control
Early fuel evaporation-mixture heater
EFE-mixture heater
Mixture heater
Early fuel evaporation system
EFE system
Mixture heater control
Electrically erasable programmable read
only memory
EEPROM
***
Electronic ignition system
EI system
Ignition timing control
Engine control
EC
***
Engine control module
ECM
ECCS control unit
Engine coolant temperature
ECT
Engine temperature
Engine coolant temperature sensor
ECTS
Engine temperature sensor
Engine modification
EM
***
Engine speed
RPM
Engine speed
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
SAE J1930 TERMINOLOGY LIST
SAE J1930 Terminology List
GI-51
NEW TERM
NEW ACRONYM /
ABBREVIATION
OLD TERM
Erasable programmable read only
memory
EPROM
***
Evaporative emission canister
EVAP canister
Canister
Evaporative emission system
EVAP system
Evaporative emission control system
Exhaust gas recirculation valve
EGR valve
EGR valve
Exhaust gas recirculation control-BPT
valve
EGRC-BPT valve
BPT valve
Exhaust gas recirculation control-solenoid
valve
EGRC-solenoid valve
EGR control solenoid valve
Exhaust gas recirculation temperature
sensor
EGRT sensor
Exhaust gas temperature sensor
EGR temperature sensor
Flash electrically erasable programmable
read only memory
FEEPROM
***
Flash erasable programmable read only
memory
FEPROM
***
Flexible fuel sensor
FFS
***
Flexible fuel system
FF system
***
Fuel level sensor
***
***
Fuel pressure regulator
***
Pressure regulator
Fuel pressure regulator control solenoid
valve
***
PRVR control solenoid valve
Fuel tank temperature sensor
FTT sensor
Tank fuel temperature sensor
Fuel trim
FT
***
Heated oxygen sensor
HO2S
Exhaust gas sensor
Idle air control system
IAC system
Idle speed control
Idle air control valve-air regulator
IACV-air regulator
Air regulator
Idle air control valve-auxiliary air control
valve
IACV-AAC valve
Auxiliary air control (AAC) valve
Idle air control valve-FICD solenoid valve
IACV-FICD solenoid valve
FICD solenoid valve
Idle air control valve-idle up control sole-
noid valve
IACV-idle up control solenoid valve
Idle up control solenoid valve
Idle speed control-FI pot
ISC-FI pot
FI pot
Idle speed control system
ISC system
***
Ignition control
IC
***
Ignition control module
ICM
***
Indirect fuel injection system
IFI system
***
Intake air
IA
Air
Intake air temperature sensor
IAT sensor
Air temperature sensor
Knock
***
Detonation
Knock sensor
KS
Detonation sensor
SAE J1930 TERMINOLOGY LIST
SAE J1930 Terminology List (Cont’d)
GI-52
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст