Infiniti I30 (A33). Manual — part 544
ENGINE LUBRICATION &
COOLING SYSTEMS
CONTENTS
ENGINE LUBRICATION SYSTEM. . . . . . . . ..2
Precautions . . . . . . . . . . . . . . . . ..2
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
. . 2
LIQUID GASKET APPLICATION PROCEDURE
. . . 2
Preparation . . . . . . . . . . . . . . . . ..3
. . . . . . . . . . 3
Lubrication Circuit . . . . . . . . . . . . . . 4
Oil Pressure Check. . . . . . . . . . . . . ..5
Oil Pump . . . . . . . . . . . . . . . . . ..5
. . . . . . . . .5
. . . . . . . . . . . 6
. . . . . . . 7
. . . . . . . . . . . . . . . ...7
Service Data and Specifications (SDS). . . . . ...7
. . . . . . . . . . . . . . 7
. . . . . . . . . . . . .7
. . . . . . . . . . . . . . . . .7
ENGINE COOLING SYSTEM. . . . . . . . . . ..8
Precautions . . . . . . . . . . . . . . . . ..8
LIQUID GASKET APPLICATION PROCEDURE
. . . 8
Preparation . . . . . . . . . . . . . . . . ..8
. . . . . . . . . . 8
Cooling Circuit . . . . . . . . . . . . . . . .9
System Check. . . . . . . . . . . . . . . 10
. . . . ...10
. . . . . . . . . . . 10
. . . . . . . . . 10
CHECKING COOLING SYSTEM FOR LEAKS
. . . 11
Water Pump . . . . . . . . . . . . . . . ... 11
. . . . . . . ... 11
. . . . . . . . . . . . . . . ... 11
. . . . . . . . . . . . . . ...13
. . . . . . . . . . . . . . 13
Thermostat. . . . . . . . . . . . . . . . .15
. . . . . . . ...15
. . . . . . . . . . . . . . ...15
Water Control Valve. . . . . . . . . . . . ...16
. . . . . . . ...16
. . . . . . . . . . . . . . ...16
Radiator . . . . . . . . . . . . . . . . . .17
. . . . . . . ...17
Cooling Fan Control System . . . . . . . . . .18
Refilling Engine Coolant . . . . . . . . . . . 18
Radiator (Aluminum type). . . . . . . . . . ..18
. . . . . . . . . . . . . ...18
. . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . .19
. . . . . . . . . . . . . . ...21
Overheating Cause Analysis . . . . . . . . . .22
Service Data and Specifications (SDS). . . . . .23
. . . . . . . . . . . . . . 23
. . . . . . . . . ...23
. . . . . . . . . . . . . . . ..23
GI
MA
EM
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
Precautions
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) “AIR BAG” AND “SEAT BELT
PRE-TENSIONER”
NHLC0036
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER” used along with
a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of
collision. The SRS system composition which is available to NISSAN MODEL A33 is as follows (The compo-
sition varies according to optional equipment.):
I
For a frontal collision
The Supplemental Restraint System consists of driver air bag module (located in the center of the steer-
ing wheel), front passenger air bag module (located on the instrument panel on passenger side), seat belt
pre-tensioners, a diagnosis sensor unit, crash zone sensor, warning lamp, wiring harness and spiral cable.
I
For a side collision
The Supplemental Restraint System consists of front side air bag module (located in the outer side of front
seat), satellite sensor, diagnosis sensor unit (one of components of air bags for a frontal collision), wiring
harness, warning lamp (one of components of air bags for a frontal collision).
Information necessary to service the system safely is included in the RS section of this Service Manual.
WARNING:
I
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance should be per-
formed by an authorized NISSAN dealer.
I
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the RS section.
I
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified with yellow harness connector (and with
yellow harness protector or yellow insulation tape before the harness connectors).
SEM164F
AEM080
LIQUID GASKET APPLICATION PROCEDURE
NHLC0001
1.
Use a scraper to remove all traces of old liquid gasket from
mating surfaces and grooves. Also, completely clean any oil
from these areas.
2.
Apply a continuous bead of liquid gasket to mating surfaces.
(Use Genuine RTV silicone sealant Part No. 999MP-A7007
or equivalent.)
I
For oil pan, be sure liquid gasket diameter is 3.5 to 4.5 mm
(0.138 to 0.177 in) or 4.5 to 5.5 mm (0.177 to 0.217 in) as
specified.
3.
Apply liquid gasket around the inner side of bolt holes (unless
otherwise specified).
4.
Assembly should be done within 5 minutes after coating.
5.
Wait at least 30 minutes before refilling engine oil and engine
coolant.
ENGINE LUBRICATION SYSTEM
Precautions
LC-2
Preparation
SPECIAL SERVICE TOOLS
NHLC0002
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
ST25051001
(J25695-1)
Oil pressure gauge
NT558
Measuring oil pressure
Maximum measuring range:
2,452 kPa (25 kg/cm
2
, 356 psi)
ST25052000
(J25695-2)
Hose
NT559
Adapting oil pressure gauge to upper oil pan
WS39930000
(
—
)
Tube pressure
NT052
Pressing the tube of liquid gasket
GI
MA
EM
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ENGINE LUBRICATION SYSTEM
Preparation
LC-3
Lubrication Circuit
NHLC0003
SLC036B
SLC320B
ENGINE LUBRICATION SYSTEM
Lubrication Circuit
LC-4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст