Infiniti I30 (A33). Manual — part 95
SAT063K
11. Install differential lubricant tube on converter housing. Tighten
differential lubricant tube bolts to the specified torque. Refer to
AT-286.
SAT235F
12. Install O-ring on differential oil port of transmission case.
SAT371H
13. Install converter housing on transmission case.
I
Apply locking sealant (Loctite #518) to mating surface of
converter housing.
SAT008F
I
Tighten converter housing bolts to the specified torque.
Refer to AT-286.
SAT406DA
14. Install accumulator piston.
a.
Check contact surface of accumulator piston for damage.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (3) (Cont’d)
AT-377
SAT236FA
b.
Install O-rings on accumulator piston.
I
Apply ATF to O-rings.
Accumulator piston O-rings:
Refer to SDS, AT-383.
SAT237FA
c.
Install accumulator pistons and return springs on transmission
case.
I
Apply ATF to inner surface of transmission case.
Return springs:
Refer to SDS, AT-384.
SAT006F
15. Install lip seals for band servo oil holes on transmission case.
I
Apply petroleum jelly to lip seals.
SAT862HA
16. Install L & R oil tube and oil sleeve. Tighten L & R oil tube bolts
to the specified torque. Refer to AT-286.
SAT005F
17. Install control valve assembly.
a.
Insert manual valve into control valve assembly.
I
Apply ATF to manual valve.
ASSEMBLY
Assembly (3) (Cont’d)
AT-378
SAT094J
b.
Set manual shaft in Neutral position.
c.
Install control valve assembly on transmission case while
aligning manual valve with manual plate.
SAT416D
d.
Pass solenoid harness through transmission case and install
terminal body on transmission case by pushing it.
e.
Install stopper ring to terminal body.
SAT004F
f.
Tighten bolts I, X and
I
.
Bolt length, number and location:
Bolt
I
X
I
Bolt length “
”
mm (in)
40
(1.57)
33
(1.30)
43.5
(1.713)
Number of bolts
5
6
2
SAT003F
18. Install oil pan.
a.
Attach a magnet to oil pan.
b.
Install new oil pan gasket on transmission case.
c.
Install oil pan on transmission case.
I
Always replace oil pan bolts as they are self-sealing bolts.
I
Tighten four bolts in a criss-cross pattern to prevent dis-
location of gasket.
d.
Tighten oil pan bolts and drain plug to the specified torque.
Refer to AT-286.
GI
MA
EM
LC
EC
FE
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ASSEMBLY
Assembly (3) (Cont’d)
AT-379
SAT033J
19. Install park/neutral position (PNP) switch.
a.
Set manual shaft in P position.
b.
Temporarily install park/neutral position (PNP) switch on
manual shaft.
c.
Move selector lever to N position.
AAT469A
d.
Use a 4 mm (0.16 in) pin for this adjustment.
i.
Insert the pin straight into the manual shaft adjustment hole.
ii.
Rotate park/neutral position (PNP) switch until the pin can also
be inserted straight into hole in park/neutral position (PNP)
switch.
e.
Tighten park/neutral position (PNP) switch fixing bolts. Refer to
AT-286.
f.
Remove pin from adjustment hole after adjusting park/neutral
position (PNP) switch.
SAT768J
20. Install A/T fluid charging pipe and fluid cooler tube to transmis-
sion case. Tighten A/T fluid charging pipe and fluid cooler tube
bolts to the specified torque. Refer to AT-286.
SAT428DA
21. Install torque converter.
a.
Pour ATF into torque converter.
I
Approximately 1 liter (1-1/8 US qt, 7/8 Imp qt) of fluid is
required for a new torque converter.
I
When reusing old torque converter, add the same amount
of fluid as was drained.
SAT429D
b.
Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
ASSEMBLY
Assembly (3) (Cont’d)
AT-380
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст