Infiniti I30 (A33). Manual — part 160
SBT775
3.
Hold door glass with both hands. While raising rear end of door
glass, remove door glass from sash and away from outside the
door.
SBT776-A
4.
Disconnect regulator assembly connector.
5.
Remove bolts securing regulator assembly and guide rail, then
remove regulator assembly and guide rail.
SBT777
Inspection
NHBT0007S0101
Check regulator assembly for the following parts. Replace faulty
parts with new ones.
I
Wire for wear
I
Regulator for deformation
I
Sliding parts for lubrication
Front Door Limit Switch Reset
NHBT0008
RESET CONDITIONS
NHBT0008S01
After each of the following operations are performed, reset the limit
switch (with built-in motor).
I
Regulator removal and installation
I
Removal of motor from regulator
I
Operation of regulator as a single unit
I
Door glass removal and installation
I
Glass run removal and installation
SBT778
RESET PROCEDURES
NHBT0008S02
After installing parts, proceed as follows:
1.
Close the door window completely.
2.
Press the reset switch and open the door window completely.
3.
Release the reset switch. After making sure the reset switch
has returned to the original position, close the door window
completely.
4.
The limit switch is now reset.
CAUTION:
Be sure to manually open or close the door window. (Do not
use the automatic open-close procedures.)
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
HA
SC
EL
IDX
DOOR
Front Door Glass (Cont’d)
BT-21
Rear Door Glass
NHBT0009
I
Make sure that door glass is positioned in glass run groove.
I
Make sure that there is no abnormality when door glass is
raised or lowered.
REAR DOOR GLASS AND REGULATOR
NHBT0009S01
SBT779
I
For removal of rear door trim, refer to “DOOR TRIM”, BT-35.
I
For removal of door outside molding, refer to “EXTERIOR”,
BT-40.
I
Remove sealing screen.
SBT780
1.
Using power window main switch, raise or lower door glass
until carrier plate securing bolts are visible.
2.
Remove bolts securing carrier plate.
DOOR
Rear Door Glass
BT-22
SBT781
3.
Remove partition sash at glass run.
4.
Remove bolts and screw securing partition sash.
SBT782
5.
Hold door glass with both hands. While raising rear end of door
glass, remove door glass from sash and away from inside the
door.
SBT783
6.
Disconnect regulator assembly connector.
7.
Remove bolts securing regulator assembly and guide rail, then
remove regulator assembly and guide rail.
SBT784
8.
Remove partition glass.
SBT785
Inspection
NHBT0009S0101
Check regulator assembly for the following parts. Replace faulty
parts with new ones.
I
Wire for wear
I
Regulator for deformation
I
Sliding parts for lubrication
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
HA
SC
EL
IDX
DOOR
Rear Door Glass (Cont’d)
BT-23
Front Door Lock
NHBT0010
SBT786
I
For removal of front door trim, refer to “DOOR TRIM”, BT-35.
I
Remove sealing screen.
SBT787
BELL CRANK ADJUSTMENT
NHBT0010S01
CAUTION:
Before adjusting bell crank, make sure that rod is installed to
inside handle.
After installing door lock and inside handle, set them in the lock
position. Using a flat-bladed screwdriver, expand rod holder.
Remove rod free play at joining area and set rod in position.
After adjusting bell crank adjustments have been made, operate
door lock knob, door lock switch and door key to make sure that
they lock and unlock properly.
SBT788
OUTSIDE HANDLE ROD ADJUSTMENT
NHBT0010S02
Rotate rod holder so that rod-to-holder clearance is adjusted as
shown in the figure at left.
CAUTION:
Make sure that rod-to-holder clearance is not “0” mm (0 in),
and that rod is not held pressed.
DOOR
Front Door Lock
BT-24
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст