Infiniti I30 (A33). Manual — part 483
SEM890EA
11. Align rear timing chain case with dowel pins, then install on
cylinder head and block.
12. Tighten rear chain case bolts.
a.
Tighten bolts in numerical order shown in the figure.
b.
Repeat above step a.
I
This installation is the same procedure as that for timing chain.
Refer to “Installation”, EM-29.
SEM868E
Valve Clearance
NHEM0022
CHECKING
NHEM0022S01
Check valve clearance while engine is cold and not running.
1.
Remove intake manifold collector.
2.
Remove rocker cover ornament.
3.
Remove RH and LH rocker covers.
4.
Remove all spark plugs.
5.
Set No. 1 cylinder at TDC on its compression stroke.
I
Align pointer with TDC mark on crankshaft pulley.
I
Check that valve lifters on No. 1 cylinder are loose and valve
lifters on No. 4 are tight.
If not, turn crankshaft one revolution (360°) and align as above.
GI
MA
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
CYLINDER HEAD
Installation (Cont’d)
EM-51
SEM893E
6.
Check only those valves shown in the figure.
Crank
position
Valve
No. 1
No. 2
No. 3
No. 4
No. 5
No. 6
INT EXH INT EXH INT EXH INT EXH INT EXH INT EXH
No. 1 TDC
q
q
q
q
SEM139D
I
Using a feeler gauge, measure clearance between valve lifter
and camshaft.
I
Record any valve clearance measurements which are out of
specification. They will be used later to determine the required
replacement adjusting shim.
Valve clearance for checking (Cold):
Intake
0.26 - 0.34 mm (0.010 - 0.013 in)
Exhaust
0.29 - 0.37 mm (0.011 - 0.015 in)
SEM894E
7.
Turn crankshaft 240° and align as above.
8.
Set No. 3 cylinder at TDC on its compression stroke.
9.
Check only those valves shown in the figure.
Crank
position
Valve
No. 1
No. 2
No. 3
No. 4
No. 5
No. 6
INT EXH INT EXH INT EXH INT EXH INT EXH INT EXH
No. 3 TDC
q
q
q
q
CYLINDER HEAD
Valve Clearance (Cont’d)
EM-52
SEM958E
10. Turn crankshaft 240° and align as above.
11. Set No. 5 cylinder at TDC on its compression stroke.
12. Check only those valves shown in the figure.
Crank
position
Valve
No. 1
No. 2
No. 3
No. 4
No. 5
No. 6
INT EXH INT EXH INT EXH INT EXH INT EXH INT EXH
No. 5 TDC
q
q
q
q
13. If all valve clearances are within specification, install the fol-
lowing parts.
I
Intake manifold collector
I
RH and LH rocker covers
I
All spark plugs
I
Rocker cover ornament
SEM557EB
ADJUSTING
NHEM0022S02
Adjust valve clearance while engine is cold.
1.
Turn crankshaft, to position cam lobe on camshaft of valve that
must be adjusted upward.
2.
Place Tool (A) around camshaft as shown in figure.
Before placing Tool (A), rotate notch toward center of cyl-
inder head (See figure.), to simplify shim removal later.
CAUTION:
Be careful not to damage cam surface with Tool (A).
SEM869E
3.
Rotate Tool (A) (See figure.) so that valve lifter is pushed down.
SEM870E
4.
Place Tool (B) between camshaft and the edge of the valve
lifter to retain valve lifter.
CAUTION:
I
Tool (B) must be placed as close to camshaft bracket as
possible.
I
Be careful not to damage cam surface with Tool (B).
5.
Remove Tool (A).
GI
MA
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
CYLINDER HEAD
Valve Clearance (Cont’d)
EM-53
SEM871E
6.
Blow air into the hole to separate adjusting shim from valve
lifter.
SEM872E
SEM145D
SEM873E
7.
Remove adjusting shim using a small screwdriver and a mag-
netic finger.
8.
Determine replacement adjusting shim size following formula.
I
Using a micrometer determine thickness of removed shim.
I
Calculate thickness of new adjusting shim so valve clearance
comes within specified values.
R = Thickness of removed shim
N = Thickness of new shim
M = Measured valve clearance
Intake:
N = R + [M − 0.30 mm (0.0118 in)]
Exhaust:
N = R + [M − 0.33 mm (0.0130 in)]
Shims are available in 64 sizes from 2.32 mm (0.0913 in)
to 2.95 mm (0.1161 in), in steps of 0.01 mm (0.0004 in).
I
Select new shim with thickness as close as possible to calcu-
lated value.
SEM146D
9.
Install new shim using a suitable tool.
I
Install with the surface on which the thickness is stamped
facing down.
CYLINDER HEAD
Valve Clearance (Cont’d)
EM-54
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст