Infiniti I30 (A33). Manual — part 102
INSPECTION
NHAX0018
Thoroughly clean all parts in cleaning solvent, and dry with
compressed air. Check parts for evidence of deformation or
other damage.
Drive Shaft
NHAX0018S01
Replace drive shaft if it is twisted or cracked.
Boot
NHAX0018S02
Check boot for fatigue, cracks or wear. Replace boot with new boot
bands.
Joint Assembly (Transaxle side)
NHAX0018S03
I
Check serration for deformation. Replace if necessary.
I
Check slide joint housing for any damage. Replace if neces-
sary.
Joint Assembly (Wheel side)
NHAX0018S04
Replace joint assembly if it is deformed or damaged.
Support Bearing
NHAX0018S05
Make sure wheel bearing rolls freely and is free from noise, cracks,
pitting or wear.
Support Bearing Bracket
NHAX0018S06
Check support bearing bracket for cracks with a magnetic explora-
tion or dyeing test.
ASSEMBLY
NHAX0019
I
After drive shaft has been assembled, ensure that it
moves smoothly over its entire range without binding.
I
Use NISSAN GENUINE GREASE or equivalent after every
overhaul.
SFA800
Wheel Side
NHAX0019S01
1.
Install boot and new small boot band on drive shaft.
Cover drive shaft serration with tape so as not to damage boot
during installation.
SFA942A
2.
Set joint assembly onto drive shaft by lightly tapping it.
Install joint assembly securely, ensuring marks which were
made during disassembly are properly aligned.
GI
MA
EM
LC
EC
FE
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-13
SFA592B
3.
Pack drive shaft with specified amount of grease.
Specified amount of grease:
135 - 145 g (4.76 - 5.11 oz)
4.
Make sure that boot is properly installed on the drive shaft
groove.
Set boot so that it does not swell and deform when its length
is “L
1
”.
Length “L
1
”:
97 mm (3.82 in)
SFA443B
5.
Lock new larger and smaller boot bands securely with a suit-
able tool.
SFA313B
Dynamic Damper
NHAX0019S02
1.
Use new damper bands when installing.
2.
Install dynamic damper from stationary-joint side while holding
it securely.
Length:
“A”: 205 - 215 mm (8.07 - 8.46 in)
“B”: 50 mm (1.97 in)
SFA800
Transaxle Side
NHAX0019S03
1.
Install boot and new small boot band on drive shaft.
Cover drive shaft serration with tape so as not to damage boot
during installation.
SFA514A
2.
Install ball cage, inner race and balls as a unit, making sure the
marks which were made during disassembly are properly
aligned.
3.
Install new snap ring.
FRONT AXLE
Drive Shaft (Cont’d)
AX-14
SFA149A
4.
Pack drive shaft with specified amount of grease.
Specified amount of grease:
165 - 175 g (5.82 - 6.17 oz)
5.
Install slide joint housing, then install new snap ring.
6.
Make sure that boot is properly installed on the drive shaft
groove.
Set boot so that it does not swell and deform when its length
is “L
2
”.
Length “L
2
”:
98 mm (3.86 in)
SFA395
7.
Lock new larger and smaller boot bands securely with a suit-
able tool.
SFA618
Support Bearing
NHAX0019S04
I
Press bearing into retainer.
SFA694
I
Press drive shaft into bearing.
SFA444B
I
Install snap ring.
I
Install new dust shield.
GI
MA
EM
LC
EC
FE
AT
SU
BR
ST
RS
BT
HA
SC
EL
IDX
FRONT AXLE
Drive Shaft (Cont’d)
AX-15
Service Data and Specifications (SDS)
DRIVE SHAFT
=NHAX0020
Applied model
All
Joint type
Transaxle side
DS90
Wheel side
ZF100
Grease
Quality
Nissan genuine grease or equivalent
Capacity
g (oz)
Transaxle side
165 - 175 (5.82 - 6.17)
Wheel side
135 - 145 (4.76 - 5.11)
Boot length
mm (in)
Transaxle side “L
2
”
98 (3.86)
Wheel side “L
1
”
97 (3.82)
SFA961AA
SFA962A
WHEEL BEARING (FRONT)
NHAX0021
Wheel bearing axial end play limit
mm (in)
0.05 (0.0020)
Wheel bearing lock nut tightening torque
N·m (kg-m, ft-lb)
255 - 333 (26 - 34, 188 - 245)
FRONT AXLE
Service Data and Specifications (SDS)
AX-16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст