Infiniti I30 (A33). Manual — part 419
SEF289X
CONSULT-II Inspection Procedure
NHEL0241
“MULTI REMOTE ENT”
NHEL0241S01
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” to the data link connector.
PBR455D
3.
Turn ignition switch “ON”.
4.
Touch “START”.
SEL941W
5.
Touch “SMART ENTRANCE”.
SEL273W
6.
Touch “MULTI REMOTE ENT”.
SEL274W
7.
Select diagnosis mode.
“DATA MONITOR”, “ACTIVE TEST” and “WORK SUPPORT”
are available.
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
MULTI-REMOTE CONTROL SYSTEM
CONSULT-II Inspection Procedure
EL-345
CONSULT-II Application Items
NHEL0242
“MULTI REMOTE ENT”
NHEL0242S01
Data Monitor
NHEL0242S0101
Monitored Item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of door switch RH.
LOCK SW DR/AS
Indicates [ON/OFF] condition of lock signal from lock/unlock switch LH and RH.
UNLK SW DR/AS
Indicates [ON/OFF] condition of unlock signal from lock/unlock switch LH and RH.
KEY CYL LK SW
Indicates [ON/OFF] condition of lock signal from key cylinder switch.
LK BUTTON/SIG
Indicates [ON/OFF] condition of lock signal from remote controller.
UN BUTTON/SIG
Indicates [ON/OFF] condition of unlock signal from remote controller.
TRUNK BTN/SIG
Indicates [ON/OFF] condition of trunk open signal from remote controller.
PANIC BTN
Indicates [ON/OFF] condition of panic signal from remote controller.
LK/UN BTN ON
Indicates [ON/OFF] condition of lock/unlock signal at the same time from remote controller.
Active Test
NHEL0242S0102
Test Item
Description
INT/IGN ILLUM
This test is able to check interior lamp and ignition key hole illumination operation. The interior
lamp and ignition key hole illumination are turned on when “ON” on CONSULT-II screen is
touched.
HAZARD
This test is able to check hazard reminder operation. The hazard lamp turns on when “ON” on
CONSULT-II screen is touched.
HORN
This test is able to check panic alarm and horn reminder operations. The alarm activate for 0.5
seconds after “ON” on CONSULT-II screen is touched.
HEAD LAMP
This test is able to check headlamps panic alarm operation. The headlamp illuminates for 0.5
seconds after “ON” on CONSULT-II screen is touched.
TRUNK OUTPUT
This test is able to check trunk lid opener actuator operation. The trunk is unlocked when “ON”
on CONSULT-II screen is touched.
Work Support
NHEL0242S0103
Test Item
Description
REMO CONT ID CONFIR
It can be checked whether remote controller ID code is registered or not in this mode.
REMO CONT ID REGIST
Remote controller ID code can be registered.
REMO CONT ID ERASUE
Remote controller ID code can be erased.
HZRD REM SET
Hazard and horn reminder mode can be changed in this mode. The reminder mode will be
changed when “MODE SET” on CONSULT-II screen is touched.
MULTI-REMOTE CONTROL SYSTEM
CONSULT-II Application Items
EL-346
Trouble Diagnoses
NHEL0195
SYMPTOM CHART
NHEL0195S01
NOTE:
I
Always check remote controller battery before replacing
remote controller.
I
The panic alarm operation and trunk lid opener operation of
multi-remote control system do not activate with the ignition
key inserted in the ignition key cylinder.
Symptom
Diagnoses/service procedure
Reference
page
(EL-
)
All function of multi-remote control system do not
operate.
1. Remote controller battery and function check
2. Power supply and ground circuit for smart entrance control
unit check
3. Replace remote controller. Refer to ID Code Entry Procedure.
NOTE: If the result of remote controller function check with
CONSULT-II is OK, remote controller is not malfunctioning.
The new ID of remote controller cannot be
entered.
1. Remote controller battery and function check
2. Key switch (insert) check
3. Door switch check
4. Door lock/unlock switch LH check
5. Power supply and ground circuit for smart entrance control
unit check
6. Replace remote controller. Refer to ID Code Entry Procedure.
NOTE: If the result of remote controller function check with
CONSULT-II is OK, remote controller is not malfunctioning.
Door lock or unlock does not function.
(If the power door lock system does not operate
manually, check power door lock system. Refer to
EL-327.)
1. Remote controller battery and function check
2. Replace remote controller. Refer to ID Code Entry Procedure.
NOTE: If the result of remote controller function check with
CONSULT-II is OK, remote controller is not malfunctioning.
Hazard and horn reminder does not activate prop-
erly when pressing lock or unlock button of remote
controller.
1. Remote controller battery and function check
2. Hazard reminder check
3. Horn reminder check*
*: Horn chirp can be activated or deactivated.
First check the horn chirp setting. Refer to “System
Description”, EL-337.
4. Door switch check
5. Replace remote controller. Refer to ID Code Entry Procedure.
NOTE: If the result of remote controller function check with
CONSULT-II is OK, remote controller is not malfunctioning.
Interior lamp and key hole illumination operation
do not activate properly.
1. Interior lamp operation check
2. Key hole illumination operation check
3. Door switch check
GI
MA
EM
LC
EC
FE
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
MULTI-REMOTE CONTROL SYSTEM
Trouble Diagnoses
EL-347
Symptom
Diagnoses/service procedure
Reference
page
(EL-
)
Panic alarm (horn and headlamp) does not acti-
vate when panic alarm button is continuously
pressed.
1. Remote controller battery and function check
2. Theft warning operation check. Refer to “PRELIMINARY
CHECK” in “VEHICLE SECURITY SYSTEM”.
3. Key switch (insert) check
4. Replace remote controller. Refer to ID Code Entry Procedure.
NOTE: If the result of remote controller function check with
CONSULT-II is OK, remote controller is not malfunctioning.
Trunk lid does not open when trunk opener button
is continuously pressed.
1. Remote controller battery and function check
2. Trunk lid opener actuator check
3. Key switch (insert) check
4. Replace remote controller. Refer to ID Code Entry Procedure.
NOTE: If the result of remote controller function check with
CONSULT-II is OK, remote controller is not malfunctioning.
MULTI-REMOTE CONTROL SYSTEM
Trouble Diagnoses (Cont’d)
EL-348
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст