Infiniti QX56 (JA60). Manual — part 797
SUNROOF SYSTEM
RF-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
CAUTION:
• Before removal, fully close the glass lid assembly. Then, after removal, do not move the motor
assembly.
• After installing or adjusting the sunroof and glass lid, check gap alignment and sunroof operation to
prevent malfunction.
• Handle glass lid with care so not to cause damage.
Removal and Installation
INFOID:0000000005147309
CAUTION:
• Always work with a helper.
• When taking sunroof unit out, use shop cloths to protect the seats and trim from damage.
• After installing the sunroof unit or glass lid, be sure to check gap adjustment to prevent any mal-
function.
SUNROOF FRAME ASSEMBLY
NOTE:
• For easier installation, mark each point before removal.
Removal
1. Remove headlining. Refer to
INT-17, "Removal and Installation"
2. Remove the glass lid assembly. Follow the procedure for GLASS LID ASSEMBLY within this section.
3. Remove overhead console bracket.
4. Disconnect the front and rear drain hoses.
5. Remove front sunroof frame assembly bolts.
6. Remove sunroof frame assembly brackets.
7. Remove the side bolts and the sunroof frame assembly.
8. Remove the sunshade assembly as necessary. Follow the procedure for SUNSHADE ASSEMBLY within
this section.
Installation
1. Install the sunshade assembly.
2. Position the sunroof frame assembly and install the side bolts.
3. Install the sunroof brackets.
4. Install the front sunroof frame assembly bolts.
5. Connect front and rear drain hoses.
6. Install the overhead console bracket.
7. Install the glass lid assembly. Follow the procedure for GLASS LID ASSEMBLY within this section.
8. Install headlining. Refer to
INT-17, "Removal and Installation"
.
9. Perform initialization procedure. Refer to
RF-5, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement"
GLASS LID ASSEMBLY
Removal
1. Open sunshade assembly.
2. Ensure glass lid assembly is closed.
3. Remove side cover LH and RH.
RF-58
< ON-VEHICLE REPAIR >
SUNROOF SYSTEM
4. Remove the screws securing glass lid assembly to the sunroof
frame assembly.
5. Remove the glass lid assembly.
Installation
1. Position glass lid assembly to sunroof frame assembly.
2. Install the glass lid assembly screws. (First tighten left front bolt, then tighten right rear bolt on glass lid
assembly to prevent it from moving while tightening other bolts.)
3. Adjust the glass lid assembly. Refer to
.
4. Install side cover LH and RH.
WIND DEFLECTOR
Removal
1. Open the sunroof.
2. Remove screws from the left, center, and right side wind deflec-
tor holders.
3. Remove the wind deflector from the sunroof frame assembly.
Installation
Installation is in the reverse order of removal.
SUNSHADE ASSEMBLY
Removal
1. Remove the headlining. Refer to
INT-17, "Removal and Installation"
.
2. Loosen sunroof frame assembly bolts and remove both sunroof frame assembly brackets.
3. Lower rear edge of sunroof frame assembly side rails enough for clearance from roof panel.
4. Remove the two shade stoppers from the rear end of the sun-
roof frame assembly.
5. Remove the sunshade assembly from the rear end of the sun-
roof frame assembly.
Installation
Installation is in the reverse order of removal.
SUNROOF MOTOR ASSEMBLY
WIIA0252E
LIIA1099E
SBT251A
SUNROOF SYSTEM
RF-59
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
Removal
CAUTION:
• When removing the sunroof motor, be sure to place the link and wire assembly in the symmetrical
and fully closed position.
• Never run the removed sunroof motor assembly as a single unit.
1. Position the sunroof in the fully closed position.
2. Remove the roof console assembly. Refer to
INT-17, "Removal and Installation"
3. Disconnect the sunroof motor assembly harness connector (2).
⇐: Vehicle front
4. Remove the sunroof motor assembly screws (3), then remove
the sunroof motor assembly (1).
Installation
CAUTION:
Before installing the sunroof motor assembly, be sure to place the link and wire assembly in the sym-
metrical and fully closed position.
1. Move the sunroof motor assembly (1) laterally little by little so
that the gear is completely engaged into the wire on the sunroof
frame assembly and the installation surface becomes parallel.
Then, secure the sunroof motor with screws (3).
⇐:Vehicle front
2. Connect the sunroof motor assembly harness connector (2) to
the sunroof motor assembly (1).
3. Install the roof console assembly. Refer to
4. Reset the sunroof motor assembly memory. Refer to
"ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
WIIA0772E
WIIA0772E
RSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
RSU
A
B
RSU
N
O
P
CONTENTS
REAR SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
Precaution for Rear Suspension . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
ON-VEHICLE MAINTENANCE . . . . . .
REAR SUSPENSION ASSEMBLY . . . . . .
On-Vehicle Inspection and Service . . . . . . ...
Wheel Alignment Inspection . . . . . . . . . ..
ON-VEHICLE REPAIR . . . . . . . . ..
REAR SUSPENSION ASSEMBLY . . . . . .
Component . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . ...
REAR SUSPENSION MEMBER . . . . . .
Removal and Installation . . . . . . . . . . .
SHOCK ABSORBER . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ...
SUSPENSION ARM . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
FRONT LOWER LINK . . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
REAR LOWER LINK & COIL SPRING . . . .
Removal and Installation . . . . . . . . . . .
STABILIZER BAR . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR LOAD LEVELING AIR SUSPENSION
COMPRESSOR ASSEMBLY . . . . . . .
Removal and Installation . . . . . . . . . . .
CONTROL UNIT . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Initialization Procedure . . . . . . . . . . .
HEIGHT SENSOR . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст