Infiniti QX56 (JA60). Manual — part 883
SR-6
< ON-VEHICLE REPAIR >
DRIVER AIR BAG MODULE
• Replace the air bag module if it has been dropped or sus-
tained an impact.
• Do not allow oil, grease or water to come in contact with the
air bag module.
INSTALLATION
Installation is in the reverse order of removal.
• If driver air bag module is being replaced due to deployment, spiral cable must also be replaced. Refer to
SR-7, "Removal and Installation"
.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SBF814E
SPIRAL CABLE
SR-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SPIRAL CABLE
Removal and Installation
INFOID:0000000005147758
REMOVAL
CAUTION:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2. Remove the steering wheel. Refer to
ST-18, "Removal and Installation"
3. Remove the instrument lower panel LH. Refer to
.
4. Remove the column cover upper and lower.
5. Remove wiper washer switch connector, then pinch the tabs at
wiper and washer switch base and slide switch away from steer-
ing column to remove.
1.
Steering wheel
2.
Lighting and turn signal switch
3.
Wiper and washer switch
4.
Spiral cable
5.
Driver air bag module connector
6.
Column cover upper
7.
Column assembly
8.
Column cover lower
9.
Screw (Do not remove)
10. Screw
A. Refer
AWHIA0141GB
LHIA0034E
SR-8
< ON-VEHICLE REPAIR >
SPIRAL CABLE
6. While pressing tabs, pull lighting and turn signal switch toward
driver door and disconnect from base.
7. Remove the screws, release the clip, and remove the spiral
cable.
CAUTION:
• Do not disassemble spiral cable.
• Do not apply lubricant to the spiral cable.
8. Remove the spiral cable connectors.
CAUTION:
With the steering linkage disconnected, the spiral cable
may snap by turning the steering wheel beyond the limited
number of turns. The spiral cable can be turned counter-
clockwise about 2.5 turns from the neutral position.
9. Remove the steering angle sensor from the spiral cable. Refer
BRC-118, "Removal and Installation"
.
INSTALLATION
Installation is in the reverse order of removal.
• Align spiral cable correctly when installing steering wheel. Make
sure that the spiral cable is in the neutral position. The neutral
position is detected by turning left 2.5 revolutions from the right
end position and ending with the knob at the top.
• If equipped with VDC, refer to
ING ANGLE SENSOR NEUTRAL POSITION : Special Repair
for steering angle sensor adjustment.
• After the work is completed, perform self-diagnosis to make sure
no malfunction is detected. Refer to
.
CAUTION:
LHIA0035E
LHIA0036E
SHIA0193E
WGIA0038E
SPIRAL CABLE
SR-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• The spiral cable may snap due to steering operation if the
cable is not installed in the correct position.
• With the steering linkage disconnected, the cable may snap
by turning the steering wheel beyond the limited number of
turns. The spiral cable can be turned counterclockwise about
2.5 turns from the neutral position.
PHIA0275E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст