Infiniti QX56 (JA60). Manual — part 497
PARKING, LICENSE PLATE AND TAIL LAMPS
EXL-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE AND TAIL LAMPS
System Diagram
INFOID:0000000005146628
System Description
INFOID:0000000005146629
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
When the combination switch (lighting and turn signal switch) is in 1ST position, BCM detects the LIGHTING
SWITCH 1ST POSITION ON. The BCM sends a parking light ON request via the CAN communication lines to
the IPDM E/R. The IPDM E/R then activates the tail lamp relay which sends power to the parking and instru-
ment illumination circuits.
EXTERIOR LAMP BATTERY SAVER CONTROL
With the combination switch (lighting and turn signal switch) in the 2nd position and the ignition switch is
turned from ON or ACC to OFF, the battery saver feature is activated.
Under this condition, the headlamps remain illuminated for 5 minutes unless the combination switch (lighting
and turn signal switch) position is changed. If the combination switch (lighting and turn signal switch) position
is changed, then the headlamps are turned off.
This setting can be changed by CONSULT-III. Refer to
BCS-26, "BATTERY SAVER : CONSULT-III Function
.
Component Parts Location
INFOID:0000000005146630
AWLIA1753GB
1.
BCM M18, M20 (view with instrument
panel removed)
2.
IPDM E/R E122, E124
3.
Combination switch (lighting and turn
signal switch) M28
AWNIA0509ZZ
EXL-18
< FUNCTION DIAGNOSIS >
PARKING, LICENSE PLATE AND TAIL LAMPS
Component Description
INFOID:0000000005146631
Part name
Description
BCM
• Recieves lighting switch requests via BCM combination switch
reading function.
• Sends parking light request signal to the IPDM E/R.
IPDM E/R
Activates the tail lamp relay upon request of the BCM.
Combination switch (lighting and turn signal switch)
Outputs lighting requests to the BCM.
DIAGNOSIS SYSTEM (BCM)
EXL-19
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (BCM)
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000005369883
WORK SUPPORT
*: Initial setting
DATA MONITOR
ACTIVE TEST
Work Item
Setting item
Setting
BATTERY SAVER SET
ON*
With the exterior lamp battery saver function
OFF
Without the exterior lamp battery saver function
CUSTOM A/LIGHT SET-
TING
MODE1*
Normal
MODE2
More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE4
Less sensitive setting than normal setting (Turns ON later than normal operation.)
ILL DELAY SET
MODE1*
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE2
Without the func-
tion
MODE3
30 sec.
MODE4
60 sec.
MODE5
90 sec.
MODE6
120 sec.
MODE7
150 sec.
MODE8
180 sec.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC ON SW [ON/OFF]
Ignition switch (ACC) status judged from ACC signal (accessory power supply)
HI BEAM SW [ON/OFF]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW 1 [ON/OFF]
HEAD LAMP SW 2 [ON/OFF]
LIGHT SW 1ST [ON/OFF]
AUTO LIGHT SW [ON/OFF]
PASSING SW [ON/OFF]
FR FOG SW [ON/OFF]
TURN SIGNAL R [ON/OFF]
TURN SIGNAL L [ON/OFF]
DOOR SW-DR [ON/OFF]
The switch status input from front door switch LH
DOOR SW-AS [ON/OFF]
The switch status input from front door switch RH
DOOR SW-RR [ON/OFF]
The switch status input from rear door switch RH
DOOR SW-RL [ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW [ON/OFF]
The switch status input from back door switch
CARGO LAMP SW [ON/OFF]
Cargo lamp status that BCM judges from the vehicle condition
OPTICAL SENSOR [ON/OFF]
The value of exterior brightness voltage input from the optical sensor
EXL-20
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000005369884
DATA MONITOR
ACTIVE TEST
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
INFOID:0000000005369885
DATA MONITOR
Test Item
Operation
Description
TAIL LAMP
ON
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
OFF
Stops the tail lamp request signal transmission.
HEAD LAMP
HI
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
LO
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
OFF
Stops the high & low beam request signal transmission.
FR FOG LAMP
ON
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
OFF
Stops the front fog lights request signal transmission.
CARGO LAMP
ON
Transmits the cargo lamp request signal with CAN communication to
turn the lamp ON.
OFF
Stops the cargo lamp request signal transmission.
CORNERING LAMP
LH
Transmits the LH cornering lamp request signal with CAN communica-
tion to turn the lamp ON.
RH
Transmits the RH cornering lamp request signal with CAN communica-
tion to turn the lamp ON.
OFF
Stops the day time running light request signal transmission.
Monitor Item
[Unit]
Description
IGN ON SW [ON/OFF]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
HAZARD SW [ON/OFF]
The switch status input from the hazard switch
TURN SIGNAL R [ON/OFF]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L [ON/OFF]
BRAKE SW [ON/OFF]
The switch status input from the brake switch
Test Item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON.
LH
Outputs the voltage to turn the left side turn signal lamps ON.
OFF
Stops the voltage to turn the turn signal lamps OFF.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст