Infiniti QX56 (JA60). Manual — part 888
DIAGNOSIS AND REPAIR WORK FLOW
SRC-3
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000005147768
OVERALL SEQUENCE
DETAILED WORK FLOW
1.
CUSTOMER INFORMATION
Get detailed information from the customer about the symptom.
>> GO TO 2
2.
PRELIMINARY CHECK
Perform preliminary check. Refer to
SRC-13, "Trouble Diagnosis Introduction"
*1
SRC-13, "Trouble Diagnosis Intro-
duction"
*2
*3
SRC-5, "Trouble Diagnosis with
CONSULT-III"
*4
SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)"
WHIA0348E
SRC-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 3
3.
TECHNICAL SERVICE BULLETINS
Check for technical service bulletins.
>> GO TO 4
4.
USER MODE
Perform self-diagnosis using the "AIR BAG" warning lamp in User mode. Refer to
.
>> GO TO 5
5.
SELF-DIAGNOSIS
Perform SELF-DIAGNOSIS. Refer to
SRC-5, "Trouble Diagnosis with CONSULT-III"
(w/CONSULT-III) or
SRC-15, "Self-Diagnosis Function (Without CONSULT-III)"
(w/o CONSULT- III).
>> GO TO 6
6.
REPLACE PART
Replace the malfunctioning part.
>> GO TO 7
7.
FINAL CHECK
Check SRS using Diagnosis mode and User mode.
Does Diagnosis mode and User mode indicate SRS normal?
YES
>> Inspection end.
NO
>> GO TO 5
INTERMITTENTS INCIDENT
SRC-5
< BASIC INSPECTION >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
INTERMITTENTS INCIDENT
Inspection Procedure
INFOID:0000000005147769
INTERMITTENT TROUBLE
An intermittent incident may have occured in the past but is not being detected currently. This DTC will not be
detected on SELF DIAG [CURRENT], but may be viewed on SELF DIAG [PAST] using CONSULT-III.
Trouble Diagnosis with CONSULT-III
INFOID:0000000005147770
DIAGNOSTIC PROCEDURE 4
Check SRS Repair History
1.
CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
Yes
>> Self-diagnostic result “SELF-DIAG [PAST]” (previously stored in the memory) might not be erased
after repair. Go to "DIAGNOSTIC PROCEDURE 3". Refer to
SRC-15, "Self-Diagnosis Function
.
No
>> Go to "DIAGNOSTIC PROCEDURE 2". Refer to
.
SRC-6
< FUNCTION DIAGNOSIS >
SRS AIR BAG SYSTEM
FUNCTION DIAGNOSIS
SRS AIR BAG SYSTEM
SRS Configuration
INFOID:0000000005147771
The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
The collision modes for which supplemental restraint systems are activated are different among the SRS sys-
tems. For example, the driver air bag module, front passenger air bag module, front seat belt pre-tensioners
and seat belt buckle pre-tensioner assemblies are activated in a frontal collision but not in a side collision.
SRS configurations for some collision modes are as follows:
WHIA0215E
SRS configuration
Frontal collision
Left side collision
Right side colli-
sion
Rollover
Driver air bag module
x
—
—
—
Front passenger air bag module
x
—
—
—
Front LH seat belt pre-tensioner
x
—
—
x
Front LH seat belt buckle pre-tensioner assembly
x
—
—
x
Front RH seat belt pre-tensioner
x
—
—
x
Front RH seat belt buckle pre-tensioner assembly
x
—
—
x
Front LH side air bag module
—
x
—
—
Front RH side air bag module
—
—
x
—
LH side curtain air bag module
—
x
—
x
RH side curtain air bag module
—
—
x
x
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст