Infiniti QX56 (JA60). Manual — part 637
INL-76
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
General precautions for service operations
INFOID:0000000005146753
• When removing or disassembling any part, be careful not to damage or deform it. Protect parts which may
get in the way with cloth.
• When removing parts with a screw driver or other tool, protect parts by wrapping them with vinyl or tape.
• Keep removed parts protected with cloth.
• If an non-reuseable part is removed, replace it with a new one.
• After re-assembly has been completed, make sure each part functions correctly.
• Never work with wet hands.
• Turn the lighting switch OFF before disconnecting and connecting the connector.
• Do not use organic solvent (paint thinner or gasoline) to clean lamps or remove sealant residue.
INTERIOR ROOM LAMP
INL-77
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ON-VEHICLE REPAIR
INTERIOR ROOM LAMP
Removal and Installation
INFOID:0000000005146754
MAP LAMP
Removal
1. Remove overhead console (3). Refer to
.
2. Disconnect connectors (4) and remove the map lamp screws
(1), then remove map lamp (2) from overhead console.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Using a suitable tool (A), remove map lamp lens (1).
: Pawl
2. Release one side of the bulb (2) from the tab, then pull straight
downward to remove.
CAUTION:
Wrap a cloth around tool to protect the housing and lens.
VANITY MIRROR LAMP
Removal
The vanity mirror lamp is replaced as part of the sunvisor assembly. Refer to
INT-17, "Removal and Installa-
.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
ALLIA0318ZZ
Map lamp bulb
: 12V - 8W
ALLIA0319ZZ
INL-78
< ON-VEHICLE REPAIR >
INTERIOR ROOM LAMP
1. Using a suitable tool (A), release the tabs and remove the vanity
mirror lamp lens (1).
: Pawl
2. Release one side of the bulb (2) from the tab, then pull straight
out to remove.
CAUTION:
Wrap a cloth around tool to protect the housing and lens.
GLOVE BOX LAMP
Removal
1. Remove instrument lower panel RH and glove box. Refer to
IP-17, "Removal and Installation"
2. Rotate glove box lamp socket and rotate counterclockwise to release from steering member.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Remove instrument lower panel RH and glove box. Refer to
IP-17, "Removal and Installation"
2. Pull bulb (2) straight out from glove box lamp socket (1) to
remove.
STEP LAMP
Removal
Vanity mirror lamp bulb
: 12V - 1.8W
ALLIA0320ZZ
Glove box lamp bulb
: 12V - 3.4W
ALLIA0321ZZ
INTERIOR ROOM LAMP
INL-79
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
1. Insert a suitable tool between door finisher and step lamp lens/socket to release the pawls.
2. Disconnect the step lamp connector, then remove step lamp.
Installation
Installation is in the reverse order of removal.
Bulb Replacement
1. Remove the step lamp lens/socket.
2. Pull the bulb straight out to remove.
PERSONAL LAMP (if equipped)
Removal
1. Remove overhead console. Refer to
.
2. Remove personal lamp screws (3).
3. Disconnect personal lamp electrical connectors (1), then
remove personal lamps (2) from overhead console.
Installation
ALLIA0013ZZ
1.
Step lamp connector
2.
Door finisher
3.
Step lamp lens/socket
4.
Step lamp bulb
Vehicle front
Step lamp bulb
: 12V - 3.8W
ALLIA0322ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст