Infiniti QX56 (JA60). Manual — part 607
INTAKE SENSOR
HAC-85
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
After disconnecting intake sensor connector, measure resistance
between terminals 1 and 2 at sensor harness side, using the table
below.
If NG, replace intake sensor. Refer to
VTL-11, "Removal and Installa-
.
Temperature
°C (°F)
Resistance k
Ω
−15 (5)
209.0
−10 (14)
160.0
−5 (23)
123.0
0 (32)
95.8
5 (41)
74.9
10 (50)
58.9
15 (59)
46.7
20 (68)
37.3
25 (77)
30.0
30 (86)
24.2
35 (95)
19.7
40 (104)
16.1
45 (113)
13.2
WJIA1378E
HAC-86
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
POWER SUPPLY AND GROUND CIRCUIT FOR CONTROLLER
POWER SUPPLY AND GROUND CIRCUIT FOR CONTROLLER
Component Description
INFOID:0000000005147729
COMPONENT DESCRIPTION
A/C auto amp.
The A/C auto amp. has a built-in microcomputer which processes
information sent from various sensors needed for air conditioner
operation. The air mix door motors, mode door motor, intake door
motor, defroster door motor, blower motor and compressor are then
controlled.
The A/C auto amp. is unitized with control mechanisms. When the
various switches and temperature dials are operated, data is input to
the A/C auto amp.
Self-diagnostic functions are also built into the A/C auto amp. to pro-
vide quick check of malfunctions in the auto air conditioner system.
Potentio Temperature Control (PTC)
There are two PTCs (driver and passenger) built into the A/C auto
amp. They can be set at an interval of 0.5
°C (1.0°F) in the 18°C
(60
°F) to 32°C (90°F) temperature range by rotating the temperature
dial. The set temperature is displayed.
A/C Auto Amp. Component Function Check
INFOID:0000000005147730
SYMPTOM: A/C system does not come on.
INSPECTION FLOW
1.
CONFIRM SYMPTOM BY PERFORMING OPERATIONAL CHECK - AUTO MODE
1. Press AUTO switch.
2. Display should indicate AUTO. Confirm that the compressor clutch engages (sound or visual inspection).
(Discharge air and blower speed will depend on ambient, in-vehicle and set temperatures.)
Can a symptom be duplicated?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
PERFORM COMPLETE OPERATIONAL CHECK
Perform a complete operational check and check for any symptoms. Refer to
Can a symptom be duplicated?
YES
>> Refer to
HAC-3, "How to Perform Trouble Diagnosis For Quick And Accurate Repair"
.
NO
>> System OK.
3.
CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4.
4.
CHECK POWER AND GROUND CIRCUIT
AWIIA0573ZZ
AWIIA0211GB
POWER SUPPLY AND GROUND CIRCUIT FOR CONTROLLER
HAC-87
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Check main power supply and ground circuit. Refer to
HAC-87, "A/C Auto Amp Power and Ground Diagnosis
.
Is the inspection result normal?
YES
>> System OK.
NO
>> Replace A/C auto amp. Refer to
VTL-7, "Removal and Installation"
.
A/C Auto Amp Power and Ground Diagnosis Procedure
INFOID:0000000005147731
Regarding Wiring Diagram information, refer to
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM
SYMPTOM: A/C system does not come on.
1.
CHECK POWER SUPPLY CIRCUITS FOR A/C AUTO AMP.
1. Turn ignition switch ON.
2. Check voltage between A/C auto amp. harness connector M49
(B) terminal 15 and M50 (A) terminal 27, and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check 10A fuses [Nos. 8 and 19, located in the fuse block (J/B)]. Refer to
.
• If fuses are OK, check harness for open circuit. Repair or replace as necessary.
• If fuses are NG, replace fuse and check harness for short circuit. Repair or replace as neces-
sary.
2.
CHECK GROUND CIRCUIT FOR A/C AUTO AMP.
AWIIA0212GB
Terminals
Ignition switch position
(+)
(-)
OFF
ACC
ON
A/C auto
amp. con-
nector
Terminal No.
M49
15
Ground
Approx. 0V
Approx. 0V
Battery
voltage
M50
27
Battery
voltage
Battery
voltage
Battery
voltage
AWIIA1073ZZ
HAC-88
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
POWER SUPPLY AND GROUND CIRCUIT FOR CONTROLLER
1. Turn ignition switch OFF.
2. Disconnect A/C auto amp. connectors.
3. Check continuity between A/C auto amp. harness connector
M50 terminal 36 and ground.
Is the inspection result normal?
OK
>> Replace A/C auto amp. Refer to
NG
>> Repair harness or connector.
36 - Ground
: Continuity should exist.
AWIIA0214ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст