Infiniti QX56 (JA60). Manual — part 460
EC-492
< ON-VEHICLE MAINTENANCE >
[VK56DE]
EVAP LEAK CHECK
3. Apply battery voltage between the terminals of EVAP canister vent control valve to make a closed EVAP
system.
4. To locate the leak, deliver positive pressure to the EVAP system until pressure gauge points reach 1.38 to
2.76 kPa (0.014 to 0.028 kg/cm
2
, 0.2 to 0.4 psi).
5. Remove EVAP service port adapter and hose with pressure pump.
6. Locate the leak using a leak detector. Refer to
BBIA0443E
EVAP CANISTER
EC-493
< ON-VEHICLE REPAIR >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ON-VEHICLE REPAIR
EVAP CANISTER
Removal and Installation
INFOID:0000000005149509
EVAP CANISTER
Tighten EVAP canister as shown in the figure.
EVAP CANISTER VENT CONTROL VALVE
1. Turn EVAP canister vent control valve counterclockwise.
2. Remove the EVAP canister vent control valve.
Always replace O-ring with a new one.
Component Inspection
INFOID:0000000005149510
EVAP CANISTER
Check EVAP canister as follows:
1. Block port B.
2. Blow air into port Aand check that it flows freely out of port C.
3. Release blocked port B.
4. Apply vacuum pressure to port B and check that vacuum pres-
sure exists at the ports Aand C.
5. Block port Aand B.
6. Apply pressure to port C and check that there is no leakage.
: N-·m (kg-m, in-lb)
BBIA0349E
BBIA0350E
PBIB1212E
EC-494
< ON-VEHICLE REPAIR >
[VK56DE]
INTAKE VALVE TIMING CONTROL
INTAKE VALVE TIMING CONTROL
Intake Valve Timing Control Solenoid Valve (LH)
INFOID:0000000005149511
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-24, "Removal and Installation"
.
2. Remove air duct and resonator assembly. Refer to
EM-24, "Removal and Installation"
3. Remove drive belt. Refer to
EM-13, "Removal and Installation"
.
4. Disconnect Intake valve timing controlintake valve timing control solenoid valve connector (LH).
5. Remove Intake valve timing control solenoid valve (LH) (2) from
Intake valve timing control solenoid valve cover (LH) (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the O-ring (3) of the Intake valve timing control solenoid valve with a new one, then lubricate
O-ring with engine oil before installing.
Intake Valve Timing Control Solenoid Valve (RH)
INFOID:0000000005149512
REMOVAL
1. Remove drive belt. Refer to
EM-13, "Removal and Installation"
.
2. Disconnect Intake valve timing control solenoid valve connector (RH).
3. Remove Intake valve timing control solenoid valve (RH) (3) from
Intake valve timing control solenoid valve cover (RH) (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the O-ring (2) of the Intake valve timing control solenoid valve with a new one, then lubricate
O-ring with engine oil before installing.
AWBIA0145ZZ
Intake valve timing control sole-
noid valve bolt
: 9.6 N·m (0.98 kg-m, 85 in-lb)
AWBIA0144ZZ
Intake valve timing control sole-
noid valve bolt
: 9.6 N·m (0.98 kg-m, 85 in-lb)
INTAKE VALVE TIMING CONTROL
EC-495
< ON-VEHICLE REPAIR >
[VK56DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Intake Valve Timing Control Position Sensor (LH)
INFOID:0000000005149513
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-24, "Removal and Installation"
.
2. Remove air duct and resonator assembly. Refer to
EM-25, "Removal and Installation"
3. Disconnect intake valve timing control position sensor connector (LH).
4. Remove intake valve timing control position sensor (LH) (1) from
Intake valve timing control solenoid valve cover (LH) (3).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the O-ring (2) of the intake valve timing control position sensor with a new one, then lubricate
O-ring with engine oil before installing.
Intake Valve Timing Control Position Sensor (RH)
INFOID:0000000005149514
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-24, "Removal and Installation"
.
2. Disconnect intake valve timing control position sensor connector (RH).
3. Remove intake valve timing control position sensor (RH) (1)
from Intake valve timing control solenoid valve cover (RH) (3).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the O-ring (2) of the intake valve timing control position sensor with a new one, then lubricate
O-ring with engine oil before installing.
Camshaft Position Sensor (PHASE)
INFOID:0000000005149515
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-24, "Removal and Installation"
.
2. Remove air duct and resonator assembly. Refer to
EM-25, "Removal and Installation"
3. Disconnect camshaft position sensor connector.
AWBIA0141ZZ
Intake valve timing control position sensor bolt
: 9.6 N·m (0.98 kg-m, 85 in-lb)
AWBIA0143ZZ
Intake valve timing control position sensor bolt
: 9.6 N·m (0.98 kg-m, 85 in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст