Infiniti QX56 (JA60). Manual — part 573
GW-18
< ON-VEHICLE REPAIR >
REAR DOOR GLASS AND REGULATOR
REAR DOOR GLASS AND REGULATOR
Removal and Installation
INFOID:0000000005147162
REAR DOOR GLASS
Removal
1. Remove the rear door finisher. Refer to
INT-11, "Removal and Installation"
.
2. Position aside the vapor shield.
3. Temporarily reconnect the power window switch.
4. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
5. Partially remove the inside seal.
6. Remove the glass run from the partition glass.
7. Remove the partition sash bolt (lower) and screw (upper) to
remove the sash.
8. Remove the glass bolts and glass.
Installation
Installation is in the reverse order of removal.
Fitting Inspection
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and carrier plate bolts to correct the glass position.
REAR DOOR GLASS REGULATOR
WIIA0942E
SIIA0290E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
REAR DOOR GLASS AND REGULATOR
GW-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal
1. Remove the rear door finisher. Refer to
INT-11, "Removal and Installation"
.
2. Position aside the vapor shield.
3. Temporarily reconnect the power window switch.
4. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
5. Remove the inside seal.
6. Remove the glass bolts.
7. Raise the glass and hold in place with suitable tool.
8. Remove the bolts, and the regulator and guide channel.
9. Disconnect the connector from the regulator assembly.
Inspection after removal
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Spring damage
• Grease condition for each sliding part
Installation
1. Connect the harness connector to the regulator assembly and
install the regulator and guide channel.
SIIA0290E
SIIA0291E
SIIA0291E
GW-20
< ON-VEHICLE REPAIR >
REAR DOOR GLASS AND REGULATOR
2. Install the glass from outside to ensure that it is in both the front
and rear glass channels. Tighten glass bolts to the specified
torque.
3. Reposition the vapor shield.
4. Install the rear door finisher. Refer to
.
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
SIIA0290E
SIDE WINDOW GLASS
GW-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
SIDE WINDOW GLASS
Removal and Installation
INFOID:0000000005147163
REMOVAL
1. Remove the luggage side finisher lower and upper. Refer to
INT-19, "Removal and Installation"
2. Disconnect the rear side window motor harness.
3. Remove the rear side window motor mounting bolts.
4. Remove the rear side window front mounting nuts.
INSTALLATION
1. Install the glass from outside to insure that it is even with the top and bottom of the opening. Tighten rear
side window front mounting nuts to the specified torque.
2. Install rear side window motor mounting bolts. Tighten rear side window latch mounting bolts to the speci-
fied torque.
3. Connect the rear side window motor harness.
4. Install luggage side finisher upper and lower . Refer to
INT-19, "Removal and Installation"
.
1.
Rear side window glass
2.
Rear side window motor
3.
Weatherstrip
4.
Inner panel
5.
Outer panel
LIIA0965E
Glass mounting nuts
: 4.2 N·m (0.43 kg-m, 37 in-lb)
Motor mounting bolts : 5.6 N·m (0.57 kg-m, 49 in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст