Infiniti QX56 (JA60). Manual — part 986
TM-246
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
Take care with order of plates.
• Snap ring (1)
• Retaining plate (2)
• Drive plate (3)
• Driven plate (4)
• Dish plate (5)
• Driveplate/Driven plate: 7/7
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
22. Measure clearance (A) between retaining plate and snap ring. If
not within specified clearance, select proper retaining plate.
WCIA0625E
SCIA5249E
SCIA2439E
Clearance “A”
: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate
: Refer to
.
SCIA3129E
ASSEMBLY
TM-247
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
23. Install needle bearing to transmission case.
CAUTION:
• Take care with the direction of needle bearing. Refer to
TM-201, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
24. Install output speed sensor (1) to transmission case and tighten
bolt (
) to specified torque.
CAUTION:
• Do not subject sensor to impact by dropping or hitting it.
• Do not disassemble sensor.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place sensor in an area affected by magnetism.
25. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
26. Install return spring (1) to parking pawl (2).
SCIA5031E
Output speed sensor bolt : 5.8 N·m (0.59 kg-m, 51 in-lb)
JSDIA1321ZZ
Tool number
: ST33400001 (J-26082)
WCIA0475E
SCIA6180J
TM-248
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
29. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
SCIA3424E
SCIA3423E
SCIA6179J
SCIA5209E
SCIA5247E
ASSEMBLY
TM-249
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
32. Install output shaft in transmission case.
CAUTION:
Do not mistake front of shaft for rear because both sides
look similar (thinner end is front side).
33. Install bearing race to output shaft.
34. Install rear extension assembly (2WD models) or adapter case assembly (4WD models) according to the
following procedures.
a. 2WD models
i.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.) to rear extension assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the transmission case and rear exten-
sion assembly mating surfaces.
ii.
Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5030E
SCIA5245E
SCIA5212E
SCIA5029E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст