Infiniti QX56 (JA60). Manual — part 20
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-71
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4. Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch to ACC.
3. Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-175, "Removal and Installation"
.
5.
CHECK CHANGEOVER SWITCH
Check changeover switch.
ADP-72, "CHANGEOVER SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-38, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
ADP-177, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-175, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
Automatic drive positioner control
unit connector
Terminal
Ground
Continuity
M33 (A)
2
No
18
Door mirror remote control switch
connector
Terminal
Ground
Continuity
D10
7
Yes
ALJIA0189ZZ
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector
Terminal
M33
2
Ground
5
18
PIIA4767E
ADP-72
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH : Component Inspection
INFOID:0000000005147513
1.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace door mirror remote control switch. Refer to
ADP-177, "Removal and Installation"
MIRROR SWITCH
MIRROR SWITCH : Description
INFOID:0000000005147514
It operates angle of the door mirror face.
It transmits mirror face adjust operation to automatic drive positioner control unit.
MIRROR SWITCH : Component Function Check
INFOID:0000000005147515
1.
CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
ADP-28, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Mirror switch function is OK.
NO
>> Refer to
ADP-72, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000005147516
Regarding Wiring Diagram information, refer to
1.
CHECK MIRROR SWITCH FUNCTION
1. Turn ignition switch to ACC.
2. Check voltage between automatic drive positioner control unit
connector and ground.
Terminal
Change over switch
condition
Continuity
Door mirror remote control switch
10
7
LEFT
Yes
Other than above
No
11
RIGHT
Yes
Other than above
No
ALJIA0272ZZ
PIIA4771E
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-73
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 6
NO
>> GO TO 2
2.
CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror remote control switch.
3. Check continuity between automatic drive positioner control unit
connector and door mirror remote control switch connector.
4. Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 3
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Terminals
Mirror switch
Condition
Voltage (V)
(Approx.)
(+)
(–)
Automatic drive
positioner control
unit connector
Terminal
M33
3
Ground
UP
0
Other than above
5
4
LEFT
0
Other than above
5
19
DOWN
0
Other than above
5
20
RIGHT
0
Other than above
5
Automatic drive
positioner control
unit connector
Terminal
Door mirror remote
control switch con-
nector
Terminal
Continuity
M33 (A)
3
D10 (B)
15
Yes
4
13
19
12
20
4
Automatic drive positioner
control unit connector
Terminal
Ground
Continuity
M33 (A)
3
No
4
19
20
ALJIA0191ZZ
ADP-74
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Check continuity between door mirror remote control switch connec-
tor and ground.
Is the inspection result normal?
YES
>> GO TO 4
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch to ACC.
3. Check voltage between automatic drive positioner control unit
and ground.
Is the inspection result normal?
YES
>> GO TO 5
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-175, "Removal and Installation"
5.
CHECK MIRROR SWITCH
Check mirror switch.
ADP-74, "MIRROR SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-38, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
ADP-177, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
GI-38, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-175, "Removal and Installation"
NO
>> Repair or replace the malfunctioning parts.
MIRROR SWITCH : Component Inspection
INFOID:0000000005147517
1.
CHECK MIRROR SWITCH
Door mirror remote control
switch connector
Terminal
Ground
Continuity
D10
7
Yes
ALJIA0189ZZ
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector
Terminal
M33
3
Ground
5
4
19
20
PIIA4771E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст