Infiniti QX56 (JA60). Manual — part 319
PROPELLER SHAFT
DLN-199
< DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DISASSEMBLY AND ASSEMBLY
PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000005148909
DISASSEMBLY
Journal
1. Put matching marks on the rear propeller shaft and flange yoke
as shown.
CAUTION:
For matching marks use paint. Never damage the rear pro-
peller shaft or flange yoke.
2. Remove the snap rings.
3. Push out and remove the journal bearings by lightly tapping the
flange yoke with a hammer, taking care not to damage the jour-
nal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
4. Push out and remove the remaining journal bearings at the
opposite side by lightly tapping the flange yoke with a hammer,
taking care not to damage the journal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
ASSEMBLY
SPD128
APD011
SPD732
SPD131
DLN-200
< DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2S1410]
PROPELLER SHAFT
Journal
1. Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2. Select new snap rings that will provide the specified play in an
axial direction of the journal, and install them. Refer to
.
CAUTION:
Do not reuse snap rings
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
3. Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4. Make sure that the journal moves smoothly and is below the joint flex effort specification. Refer to
.
WPD019
APD012
SPD732
Standard
Propeller shaft joint flex ef-
fort
: Refer to
LDIA0119E
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-201
< SERVICE DATA AND SPECIFICATIONS (SDS)
[PROPELLER SHAFT: 2S1410]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000005148910
Propeller Shaft Runout
Unit: mm (in)
Propeller Shaft Joint Flex Effort
Unit: N·m (kg-m, in-lb)
Journal Axial Play
Unit: mm (in)
Snap Ring
INFOID:0000000005148911
Model (2WD)
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Model (4WD)
Unit: mm (in)
Applied model
2WD
4WD
VK56DE
A/T
Propeller shaft model
2S1410
Number of joints
2
Coupling method with rear final drive
Flange type
Coupling method with transfer
Sleeve type
Shaft length (Spider to spider)
1637.1 (44.35)
1156.8 (45.54)
Shaft outer diameter
127.60 (5.02)
102.46 (4.03)
Item
Limit
Propeller shaft runout
1.02 (0.0402) or less
Item
Limit
Propeller shaft joint flex effort
2.26 (0.23, 20) or less
Item
Limit
Journal axial play
0.02 (0.0008) or less
Thickness
Color
Part Number*
1.600 - 1.638 (0.0630 - 0.0645)
Black
37146-EA500
1.549 - 1.588 (0.0610 - 0.0625)
Black
37147-EA500
1.524 - 1.562 (0.0600 - 0.0615)
Black
37148-EA500
1.499 - 1.537 (0.0590 - 0.0605)
Black
37149-EA500
Thickness
Color
Part Number*
1.99 (0.0783)
White
37146-C9400
2.02 (0.0795)
Yellow
37147-C9400
2.05 (0.0807)
Red
37148-C9400
2.08 (0.0819)
Green
37149-C9400
2.11 (0.0831)
Blue
37150-C9400
DLN-202
< SERVICE DATA AND SPECIFICATIONS (SDS)
[PROPELLER SHAFT: 2S1410]
SERVICE DATA AND SPECIFICATIONS (SDS)
*Always check with the Parts Department for the latest parts information.
2.14 (0.0843)
Light brown
37151-C9400
2.17 (0.0854)
Black
37152-C9400
2.20 (0.0866)
No paint
37153-C9400
Thickness
Color
Part Number*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст