Infiniti QX56 (JA60). Manual — part 536
EXT-14
< SERVICE INFORMATION >
FRONT BUMPER
REMOVAL
1. Remove the side screws from the front fascia assembly.
2. Remove the screws from the front of fender protector. Refer to
3. Remove the fog turn/fog lamp finisher and the fog turn/fog lamp.
• Disconnect the harnesses.
4. Disconnect the sonar sensor, if equipped harness connector under the front fascia assembly.
5. Remove the fasteners, release the clips and remove the front fascia assembly.
6. Remove the plastic clips and remove the upper energy absorber.
7. Remove the upper bumper reinforcement.
8. Remove the plastic clips and remove the lower energy absorber.
9. Remove the front bumper stays and the front bumper side brackets, LH and RH.
10. Disconnect the sonar sensors, if equipped from the sonar sensor retainers, if equipped.
11. Remove the sonar sensors, if equipped and harness from the front fascia assembly.
• Disconnect the sonar sensors, if equipped from the harness.
• Remove the sonar sensor retainers, if equipped from the front fascia assembly.
INSTALLATION
Installation is in the reverse order of removal.
7.
Sonar sensor harness (if equipped)
8.
Front fascia assembly
9.
Sonar sensor retainers (if equipped)
10. Engine under cover
11. Front fascia bracket
12. License plate bracket
13. Fog turn/fog lamp finisher LH/RH
14. Fog turn/fog lamp
15. Front bumper stay LH
16. Front bumper side bracket LH
17. Headlamp finisher (RH shown)
A.
Clip C103
B.
Clip CS101
REAR BUMPER
EXT-15
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REAR BUMPER
Removal and Installation
INFOID:0000000005147319
1.
Retainer assembly
2.
Clip C103
3.
S clip
4.
Energy absorber
5.
Sonar sensors
6.
Sonar sensor harness
7.
Quarter panel trim cover LH
8.
Drafter duct
9.
Retainer clip
AWKIA1560ZZ
EXT-16
< SERVICE INFORMATION >
REAR BUMPER
REMOVAL
1. Remove the rear combination lamps LH and RH. Refer to
EXL-158, "Removal and Installation"
2. Remove the rear fascia assembly screws under the rear combination lamps LH and RH.
3. Remove the quarter panel trim covers LH and RH.
4. Disconnect the sonar sensor harness connector under the rear fascia assembly.
5. Release the retainer clips on both sides of the rear fascia assembly with a 1/4 turn and top S clips and
remove the fascia assembly.
6. Detach the I-key antenna from the energy absorber.
7. Remove the energy absorber.
8. Remove the reinforcement assembly.
9. Remove the nuts and remove the retainer assembly.
• Remove the S clips from the retainer assembly.
10. Disconnect the sonar sensors from the sonar sensor retainers.
11. Remove the sonar sensors and harness from the rear fascia assembly.
• Disconnect the sonar sensors from the harness.
• Remove the sonar sensor retainers from the rear fascia assembly.
12. Remove the bolts on each side of the tow hitch and remove the tow hitch.
13. Remove the drafter duct from under the LH quarter pane, if necessary.
INSTALLATION
Installation is in the reverse order of removal.
10. Rear fascia assembly
11. Sonar sensor retainer
12. Reinforcement assembly
13. Tow hitch
14. Quarter panel trim cover RH
FRONT GRILLE
EXT-17
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT GRILLE
Removal and Installation
INFOID:0000000005147320
REMOVAL
1. Remove the bolts and nuts attaching grille.
2. Remove the front grille.
INSTALLATION
Installation is in the reverse order of removal.
1.
Front grille
2.
J-Clip
AWKIA0022ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст