Infiniti FX45. Maintenance (2008 year). Manual — part 3
CHASSIS AND BODY MAINTENANCE
MA-33
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
MA
N
O
P
PAD
• Check for wear or damage.
Checking Steering Gear and Linkage
INFOID:0000000001328932
STEERING GEAR
• Check gear housing and boots for looseness, damage and grease
leakage.
• Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
Checking Power Steering Fluid and Line
INFOID:0000000001328933
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
• Do not overfill.
• Recommended fluid is Genuine NISSAN PSF or equivalent.
Refer to
SMA922A
Front
Rear
Standard thickness
11.0 mm (0.433 in)
8.5 mm (0.335 in)
Repair limit thickness
2.0 mm (0.079 in)
2.0 mm (0.079 in)
BRA0010D
SLIA0014E
SST850C
2008 FX35/FX45
MA-34
< SERVICE INFORMATION >
CHASSIS AND BODY MAINTENANCE
• Check lines for improper attachment, leaks, cracks, damage,
loose connections, chafing and deterioration.
• Check rack boots for accumulation of power steering fluid.
Axle and Suspension Parts
INFOID:0000000001328934
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
• Shake each wheel to check for excessive play.
• Check wheel bearings for smooth operation.
• Check axle and suspension nuts and bolts for looseness.
• Check strut (shock absorber) for oil leakage or other damage.
• Check suspension ball joint for grease leakage and ball joint dust
cover for cracks or other damage.
Drive Shaft
INFOID:0000000001328935
Check boot and drive shaft for cracks, wear, damage and grease
leakage.
SST851C
SMA525A
SFA392B
SFA108A
2008 FX35/FX45
CHASSIS AND BODY MAINTENANCE
MA-35
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
MA
N
O
P
Lubricating Locks, Hinges and Hood Latch
INFOID:0000000001328936
Checking Seat Belt, Buckles, Retractors, Anchors and Adjusters
INFOID:0000000001328937
CAUTION:
• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.
• If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
PIIA7009E
PIIB7160E
2008 FX35/FX45
MA-36
< SERVICE INFORMATION >
CHASSIS AND BODY MAINTENANCE
For details, refer to Refer to Service Manual in SB section.
• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released
2008 FX35/FX45
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-37
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
MA
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
Standard and Limit
INFOID:0000000001328938
BELT DEFLECTION AND TENSION (VQ35DE)
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at different location on the belt.
BELT DEFLECTION AND TENSION (VK45DE)
ENGINE COOLANT CAPACITY (APPROXIMATE) (VQ35DE)
Unit:
(US qt, lmp qt)
ENGINE COOLANT CAPACITY (APPROXIMATE) (VK45DE)
Unit:
(US qt, lmp qt)
RADIATOR
Unit: kPa (kg/cm
2
, psi)
ENGINE OIL CAPACITY (APPROXIMATE) (VQ35DE)
Deflection adjustment
Unit: mm (in)
Tension adjustment*
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After adjustment
Limit
After adjustment
Alternator and
power steering
oil pump belt
12 (0.47)
7 - 8
(0.28 - 0.31)
6 - 7
(0.24 - 0.28)
294 (30, 66)
730 - 818
(74.5 - 83.5,
164 - 184)
838 - 926
(85.5 - 94.5,
188 - 208)
A/C compressor
belt
12 (0.47)
9 - 10
(0.35 - 0.39)
8 - 9
(0.31 - 0.35)
196 (20, 44)
348 - 436
(35.5 - 44.5,
78 - 98)
470 - 559
(48 - 57,
106 - 126)
Applied pushing
force
98 N (10 kg, 22 lb)
—
PBIC5323E
Tension of drive belts
Auto-adjustment by auto tensioner
Engine coolant capacity (With reservoir tank at “MAX” level)
8.6 (9-1/8, 7-5/8)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (7/8, 3/4)
Engine coolant capacity (With reservoir tank at “MAX” level)
10.0 (10-5/8, 8-3/4)
Reservoir tank engine coolant capacity (At “MAX” level)
0.8 (7/8, 3/4)
Cap relief pressure
Standard
78 - 98 (0.8 - 1.0, 11 - 14)
Limit
59 (0.6, 9)
Leakage testing pressure
157 (1.6, 23)
2008 FX35/FX45
MA-38
< SERVICE INFORMATION >
SERVICE DATA AND SPECIFICATIONS (SDS)
Unit:
(US qt, lmp qt)
ENGINE OIL CAPACITY (APPROXIMATE) (VK45DE)
Unit:
(US qt, lmp qt)
SPARK PLUG (PLATINUM-TIPPED TYPE) (VQ35DE)
SPARK PLUG (PLATINUM-TIPPED TYPE) (VK45DE)
WHEEL BALANCE
Drain and refill
With oil filter change
4.7 (5, 4-1/8)
Without oil filter change
4.4 (4-5/8, 3-7/8)
Dry engine (Overhaul)
5.4 (5-3/4, 4-3/4)
Drain and refill
With oil filter change
5.8 (6-1/8, 5-1/8)
Without oil filter change
5.2 (5-1/2, 4-5/8)
Dry engine (Overhaul)
7.0 (7-3/8, 6-1/8)
Make
NGK
Type
Standard
PLFR5A-11
Hot
PLFR4A-11
Cold
PLFR6A-11
Gap (Nominal)
1.1mm (0.043 in)
Make
NGK
Type
Standard
PLFR5A-11
Hot
PLFR4A-11
Cold
PLFR6A-11
Gap (Nominal)
1.1mm (0.043 in)
Maximum allowable unbalance
Dynamic (At rim flange)
Less than 5.0 g (0.18 oz) (one side)
Static (At rim flange)
Less than 20 g (0.71 oz)
2008 FX35/FX45
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст