Infiniti G35 (V35). Manual — part 228
BRAKE PEDAL
BR-7
C
D
E
G
H
I
J
K
L
M
A
B
BR
Components
NFS000I9
Removal and Installation
NFS00059
REMOVAL
1.
Remove the instrument driver lower panel. Refer to
Instrument Driver Lower Panel"
2.
Remove stop lamp switch and ASCD cancel switch from pedal
assembly.
3.
Remove snap pin and clevis pin from clevis of brake booster.
4.
Remove mounting nuts and bolt from bracket, and remove pedal
assembly from vehicle.
INSPECTION AFTER REMOVAL
●
Check brake pedal upper rivet for deformation.
●
Make sure that the lapping length of sub-bracket and slide plate
is at least 5.5 mm (0.217 in).
●
Check brake pedal for bend, damage, and cracks on the welded
parts.
●
Replace brake pedal assembly if any non-standard condition is
detected.
●
Check clevis pin and plastic stopper for damage and deforma-
tion. Replace clevis pin if there are.
SFIA1783E
SFIA0159E
SFIA2824E
SBR997
BR-8
BRAKE PEDAL
INSTALLATION
Installation is in the reverse order of the removal. Tightening torques for brake pedal assembly mounting nuts
and bolt are referred to
. Tightening torque for lock nut is referred to
●
After installing brake pedal assembly to vehicle, adjust brake pedal. Refer to
BRAKE FLUID
BR-9
C
D
E
G
H
I
J
K
L
M
A
B
BR
BRAKE FLUID
PFP:KN100
Checking Brake Fluid Level
NFS0005A
●
Check fluid level in reservoir tank. It should be between Max and
Min lines on reservoir tank.
●
If fluid level is extremely low, check brake system for leaks.
●
Release parking brake lever or pedal, and then see if brake
warning lamp goes off. If not, check brake system for leaks.
Drain and Refill
NFS0005B
CAUTION:
●
Carefully monitor brake fluid level in reservoir tank during draining operation.
●
Refill with new brake fluid “DOT3”.
●
Never reuse drained brake fluid.
●
Do not let brake fluid splash on painted surfaces of body. This might damage the paint, when
splashing it on the surfaces, immediately wipe off the m with cloth and wash it away with water.
1.
Turn ignition switch OFF and disconnect VDC actuator connectors or the battery negative terminal.
2.
Connect a vinyl tube to bleed valve.
3.
Depress brake pedal, loosen bleed valve, and gradually remove
brake fluid.
4.
Make sure there is no foreign material in the reservoir tank, and
refill with new brake fluid.
5.
Rest foot on brake pedal. Loosen bleed valve. Slowly depress
brake pedal until it stops. Tighten bleed valve. Release brake
pedal. Repeat this process a few times, then pause to add new
brake fluid to reservoir tank. Continue until new brake fluid flows
out.
6.
Bleed Air. Refer to
BR-10, "Bleeding Brake System"
.
SFIA2484E
BRA0007D
BRA0006D
BR-10
BRAKE FLUID
Bleeding Brake System
NFS0005C
CAUTION:
●
Carefully monitor brake fluid level in reservoir tank
during bleeding operation.
●
Fill reservoir with new brake fluid “DOT 3”. Make sure it
is at least half way at all times while bleeding air out of sys-
tem.
●
Place a container under master cylinder to avoid spillage of
brake fluid.
●
Turn ignition switch OFF and disconnect VDC actuator
connectors or the battery negative terminal.
●
Bleed air in the following order. Right rear brake
→
Left
front brake
→
Left rear brake
→
Right front brake
1.
Connect a transparent vinyl tube to bleed valve.
2.
Fully depress brake pedal several times.
3.
With brake pedal depressed, open bleed valve to release air.
4.
Close bleed valve to the specified torque. Refer to
(front disc brake),
(rear
disc brake).
5.
Release brake pedal slowly.
6.
Repeat steps 2 through 5 until clear brake fluid comes out
of bleed valve.
SBR995
SBR419C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст