Infiniti G35 (V35). Manual — part 788
STC-56
[TILT/TELESCOPIC]
TILT & TELESCOPIC SYSTEM
2.
CHECK TILT SWITCH INPUT/OUTPUT
1.
Disconnect ADP steering switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between ADP steering switch harness connector
and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 5.
3.
CHECK ADP STEERING SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between ADP steering switch harness connec-
tor ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
4.
CHECK TILT SWITCH
Check continuity between ADP steering switch connector.
OK or NG
OK
>> GO TO 6.
NG
>> Replace ADP steering switch.
Connector
Terminal
Voltage
M100
2
−
Ground
Approx. 5 V
3
−
Ground
SGIA1723E
Connector
Terminal
Continuity
M100
1
−
Ground
Yes
SGIA1724E
Connector
Terminal
Condition
Continuity
M100
2
−
1
Tilt up position
Yes
Neutral or tilt down position
No
3
−
1
Tilt down position
Yes
Neutral or up position
No
SGIA1725E
TILT & TELESCOPIC SYSTEM
STC-57
[TILT/TELESCOPIC]
C
D
E
F
H
I
J
K
L
M
A
B
STC
5.
CHECK HARNESS CONTINUITY
1.
Disconnect automatic drive positioner control unit connector.
2.
Check continuity between the following terminals.
–
Automatic drive positioner control unit harness connector M96
terminal 1 and ADP steering switch harness connector M100
terminal 2.
–
Automatic drive positioner control unit harness connector M96
terminal 17 and ADP steering switch harness connector M100
terminal 3.
–
Automatic drive positioner control unit harness connector M96
terminal 1 and ground.
–
Automatic drive positioner control unit harness connector M96
terminal 17 and ground.
OK or NG
OK
>> Replace Automatic drive Positioner control unit.
NG
>> Repair or replace harness.
6.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Disconnect tilt motor and telescopic motor connector.
2.
Check voltage between tilt motor and telescopic motor harness
connector ground.
OK or NG
OK
>> Replace tilt motor and telescopic motor.
NG
>> GO TO 7.
1
−
2
: Continuity should exist.
17
−
3
: Continuity should exist.
1
−
Ground
: Continuity should not exist.
17
−
Ground
: Continuity should not exist.
SGIA1726E
Connector
Terminal
Condition
Voltage (V)
M98
1- Ground
ADP steering switch ON
(UP operation)
Battery voltage
(Approx. 12 V)
ADP steering switch OFF
0 V
2 – Ground
ADP steering switch ON
(DOWN operation)
Battery voltage
(Approx. 12 V)
ADP steering switch OFF
0 V
SGIA1727E
STC-58
[TILT/TELESCOPIC]
TILT & TELESCOPIC SYSTEM
7.
CHECK TILT MOTOR CIRCUIT
1.
Disconnect automatic drive positioner control unit and tilt motor and telescopic motor connectors.
2.
Check continuity between the following terminals.
–
Automatic drive positioner control unit harness connector M97
terminal 35 and tilt motor and telescopic motor harness connec-
tor M98 terminal 1.
–
Automatic drive positioner control unit harness connector M97
terminal 42 and tilt motor and telescopic motor harness connec-
tor M98 terminal 2.
–
Automatic drive positioner control unit harness connector M97
terminal 35 and ground.
–
Automatic drive positioner control unit harness connector M97
terminal 42 and ground.
OK or NG
OK
>> Replace automatic drive positioner control unit.
NG
>> Repair or replace harness.
35
−
1
: Continuity should exist.
42
−
2
: Continuity should exist.
35
−
Ground
: Continuity should not exist.
42
−
Ground
: Continuity should not exist.
SGIA1728E
WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
A
B
WT
ROAD WHEELS & TIRES
PRECAUTIONS . . . . . . . . . . . . . . .. 3
PREPARATION . . . . . . . . . . . . . . ... 4
Special Service Tools . . . . . . . . . . . ... 4
Commercial Service Tools . . . . . . . . . . 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 5
NVH Troubleshooting Chart . . . . . . . . . . 5
ROAD WHEEL . . . . . . . . . . . . . . . 6
Inspection . . . . . . . . . . . . . . . . . 6
ALUMINUM WHEEL . . . . . . . . . . . . 6
STEEL WHEEL . . . . . . . . . . . . . . 6
ROAD WHEEL TIRE ASSEMBLY . . . . . . . .. 7
Balancing Wheels (Bonding Weight Type) . . . ... 7
REMOVAL . . . . . . . . . . . . . . . . 7
WHEEL BALANCE ADJUSTMENT . . . . . .. 7
Tire Rotation . . . . . . . . . . . . . . . . 8
DESCRIPTION . . . . . . . . . . . . . .. 8
TIRE PRESSURE MONITORING SYSTEM . . . . 10
System Components . . . . . . . . . . . .. 10
System Description . . . . . . . . . . . . 10
Can Communication . . . . . . . . . . . . 11
SYSTEM DESCRIPTION . . . . . . . . . .11
TROUBLE DIAGNOSIS . . . . . . . . . . . 12
How to Perform Trouble Diagnosis . . . . . . 12
Wiring Diagram — T/WARN — . . . . . . . .. 14
Trouble Diagnosis Chart . . . . . . . . . . . 16
TROUBLE DIAGNOSIS CHART FOR SYMP-
TOMS . . . . . . . . . . . . . . . . .. 16
Transmitter Wake Up Operation . . . . . . . . 20
WITH ACTIVATION TOOL . . . . . . . . .. 20
CONSULT-II Function (BCM) . . . . . . . . . 20
Diagnosis Procedure with Warning Lamp Function
(Without CONSULT-II) . . . . . . . . . . . 25
Preliminary Check . . . . . . . . . . . . .. 28
BASIC INSPECTION . . . . . . . . . . ... 28
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS . . . . . . . . . . . . . . . . . . 29
Transmitter or Control Unit (BCM) . . . . . . .. 29
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 29
Transmitter - 1 . . . . . . . . . . . . . . 29
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 . . . . . . . ... 29
Transmitter - 2 . . . . . . . . . . . . . . 30
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 30
Vehicle Speed Signal . . . . . . . . . . . .. 31
MALFUNCTION CODE NO. 52 . . . . . . ... 31
TROUBLE DIAGNOSIS FOR SYMPTOMS . . . .. 32
Warning Lamp Does Not Come On When Ignition
Switch Is Turned On . . . . . . . . . . . ... 32
DIAGNOSTIC PROCEDURE . . . . . . . .. 32
Warning Lamp Stays On When Ignition Switch Is
Turned On . . . . . . . . . . . . . . . .. 32
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст