Infiniti G35 (V35). Manual — part 624
LU-10
OIL FILTER
OIL FILTER
PFP:15208
Removal and Installation
NBS000L6
REMOVAL
WARNING:
Be careful not to get burned when engine and engine oil may be hot.
1.
Remove undercover with power tool.
2.
Using oil filter wrench (SST), remove oil filter.
CAUTION:
●
Oil filter is provided with relief valve. Use Genuine NIS-
SAN Oil Filter or equivalent.
●
When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
●
Do not allow engine oil to adhere to drive belts.
●
Completely wipe off any engine oil that adheres to the
engine and the vehicle.
INSTALLATION
1.
Remove foreign materials adhering to oil filter installation surface.
2.
Apply engine oil to the oil seal contact surface of new oil filter.
3.
Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
2.
Start engine, and make sure that there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level and adjust engine oil. Refer to
.
PBIC0819E
SMA010
Oil filter:
: 17.6 N·m (1.8 kg-m, 13 ft-lb)
SMA229B
OIL COOLER
LU-11
C
D
E
F
G
H
I
J
K
L
M
A
LU
OIL COOLER
PFP:21305
Components
NBS002VG
Removal and Installation
NBS002VH
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
NOTE:
When removing oil cooler only, step 2 is unnecessary.
1.
Remove undercover with power tool.
2.
Drain engine coolant from radiator and cylinder block. Refer to
CO-10, "Changing Engine Coolant"
and
NOTE:
Perform this step when removing water pipes.
3.
Remove oil filter. Refer to
.
CAUTION:
Do not spill engine oil on drive belts.
4.
Disconnect water hoses from oil cooler, while pinching hoses near oil cooler to prevent engine coolant
spilling.
CAUTION:
●
Perform this step when engine is cold.
●
Do not spill engine coolant on the drive belts.
5.
Remove connector bolt, and remove oil cooler.
1.
Oil filter
2.
Connector bolt
3.
Oil cooler
4.
O-ring
5.
Relief valve
6.
Oil pan (upper) right side
7.
Water hose
8.
Water hose
9.
Water pipe
10.
Water hose
PBIC2403E
LU-12
OIL COOLER
CAUTION:
Do not spill engine oil to rubber parts such as drive belts and engine mounting insulator.
6.
Remove water pipes, as necessary.
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler.
Relief Valve
Check relief valve for movement, cracks and breaks by pushing the ball. If replacement is necessary, remove
relief valve by prying it out with a suitable tool. Install a new relief valve in place by tapping it.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
Make sure that no foreign objects are adhering to the installation surfaces of oil cooler and oil pan (upper).
●
Align cutout on oil cooler with protrusion on oil pan (upper) side,
and tighten connector bolt.
INSPECTION AFTER INSTALLATION
1.
Check engine oil level and engine coolant level, and adjust engine oil and engine coolant. Refer to
2.
Start engine, and make sure that there is no leaks of engine oil or engine coolant.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level and the engine coolant level again. Refer to
and
KBIA1342E
OIL PUMP
LU-13
C
D
E
F
G
H
I
J
K
L
M
A
LU
OIL PUMP
PFP:15010
Components
NBS002VI
Removal and Installation
NBS002VJ
REMOVAL
1.
Remove oil pans (lower and upper) and oil strainer. Refer to
EM-29, "OIL PAN AND OIL STRAINER"
2.
Remove front timing chain case and timing chain (primary). Refer to
.
3.
Remove oil pump assembly.
INSTALLATION
CAUTION:
Before installation, apply new engine oil to the parts as instructed in the figure.
Note the following, and install in the reverse order of removal.
●
When installing, align crankshaft flat faces with inner rotor flat faces.
INSPECTION AFTER INSTALLATION
1.
After warming up engine, check for engine oil leakage.
2.
Check the engine oil level and adjust engine oil. Refer to
Disassembly and Assembly
NBS002VK
DISASSEMBLY
1.
Remove oil pump cover.
2.
Remove inner rotor and outer rotor from oil pump body.
3.
After removing regulator plug, remove regulator spring and regulator valve.
1.
Oil pump body
2.
Oil pump outer rotor
3.
Oil pump inner rotor
4.
Oil pump cover
5.
Regulator valve plug
6.
Regulator valve spring
7.
Regulator valve
SBIA0481E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст