Infiniti G35 (V35). Manual — part 528
CONSULT-II CHECKING SYSTEM
GI-37
C
D
E
F
G
H
I
J
K
L
M
B
GI
Checking Equipment
NAS0001X
When ordering the following equipment, contact your NISSAN/INFINITI distributor.
CAUTION:
●
Previous CONSULT-II “I” and “Y” DLC-I and DLC-II cables should NOT be used anymore because
their DDL connector pins can be damaged during cable swapping.
●
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self- diagnosis depending on control unit which carry out CAN communication.
●
If CONSULT-II CONVERTER is not connected with CONSULT-II, vehicle occur the “FAIL SAFE
MODE” which is “LIGHT UP the HEAD LIGHT” and /or “COOLING FAN ROTATING” when CON-
SULT-II is started.
NOTE:
●
The CONSULT-II must be used in conjunction with a program card.
CONSULT-II does not require loading (Initialization) procedure.
●
Be sure the CONSULT-II is turned off before installing or removing a program card.
CONSULT-II Start Procedure
NAS0001Y
NOTE:
Turning ignition switch off when performing CAN diagnosis could cause CAN memory to be erased.
1.
Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
2.
If necessary, turn on the ignition switch.
3.
Touch “START(NISSAN BASED VHCL)” or System Shortcut key
(eg: ENGINE) on the screen.
Tool name
Description
NISSAN CONSULT-II
1. CONSULT-II unit (Tester internal soft: Resident
version 3.3.0) and accessories
2. Program card UED06D and AEN06B (For
NATS)
3. CONSULT-II CONVERTER
4. “CONSULT-II Pigtail” Cable
SAIA0363E
PAIA0070E
SAIA0450E
GI-38
CONSULT-II CHECKING SYSTEM
4.
Touch necessary system on "SELECT SYSTEM" screen.
If necessary system is not indicated, check power supply and
ground of system control unit. If it is normal, refer to
"CONSULT-II Data Link Connector (DLC) Circuit"
.
5.
Select the desired part to be diagnosed on the "SELECT DIAG
MODE" screen.
CONSULT-II Data Link Connector (DLC) Circuit
NAS0001Z
INSPECTION PROCEDURE
If the CONSULT-II cannot diagnose the system properly, check the following items.
NOTE:
The DDL1 and DDL2 circuits from DLC pins 12, 13, 14 and 15 may be connected to more than one system. A
short in a DDL circuit connected to a control unit in one system may affect CONSULT-II access to other sys-
tems.
BCIA0030E
BCIA0031E
Symptom
Check item
CONSULT-II cannot access
any system.
●
CONSULT-II DLC power supply circuit (Terminal 8) and ground circuit (Terminal 4) (For detailed
circuit, refer to “MIL & Data Link Connectors Wiring Diagram” in EC section.)
●
CONSULT-II DLC cable and CONSULT-II CONVERTER.
CONSULT-II cannot access
individual system. (Other sys-
tems can be accessed.)
●
CONSULT-II program card (Check the appropriate CONSULT-II program card for the system.
Refer to "Checking Equipment".)
●
Power supply and ground circuit for the control unit of the system (For detailed circuit, refer to wir-
ing diagram for each system.)
●
Open or short circuit between the system and CONSULT-II DLC (For detailed circuit, refer to wiring
diagram for each system.)
●
Open or short circuit CAN communication. Refer to
LAN-47, "CAN System Specification Chart"
.
CONSULT-II CHECKING SYSTEM
GI-39
C
D
E
F
G
H
I
J
K
L
M
B
GI
CIRCUIT DIAGRAM
TAWM0055E
GI-40
LIFTING POINT
LIFTING POINT
PFP:00000
Commercial Service Tools
NAS00020
CAUTION:
●
Every time the vehicle is lifted up, maintain the complete vehicle curb condition.
●
Since the vehicle's center of gravity changes when removing main parts on the front side (engine,
transmission, suspension etc.), support a jack up point on the rear side garage jack with a mission
jack or equivalent.
●
Since the vehicle's center of gravity changes when removing main parts on the rear side (rear axle,
suspension, etc.), support a jack up point on the front side garage jack with a mission jack or
equivalent.
●
Be careful not to smash or do not do anything that would affect piping parts.
Garage Jack and Safety Stand
NAS00021
WARNING:
●
Park the vehicle on a level surface when using the jack. Make sure to avoid damaging pipes,
tubes, etc. under the vehicle.
●
Never get under the vehicle while it is supported only by the jack. Always use safety stands when
you have to get under the vehicle.
Tool name
Description
Board on attachment
Safety stand attachment
S-NT001
S-NT002
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст