Infiniti G35 (V35). Manual — part 445
FUEL PUMP
EC-661
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
NBS0011W
1.
CHECK OVERALL FUNCTION
1.
Turn ignition switch ON.
2.
Pinch fuel feed hose with two fingers.
Fuel pressure pulsation should be felt on the fuel feed hose
for 1 second after ignition switch is turned ON.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
2.
CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector
3.
Turn ignition switch ON.
4.
Check voltage between ECM terminal 113 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 3.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
113
B/OR
Fuel pump relay
[Ignition switch: ON]
●
For 1 second after turning ignition switch ON
[Engine is running]
0 - 1.5V
[Ignition switch: ON]
●
More than 1 second after turning ignition
switch ON.
BATTERY VOLTAGE
(11 - 14V)
PBIB1020E
Voltage: Battery voltage
PBIB1187E
EC-662
FUEL PUMP
3.
CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I
1.
Disconnect IPDM E/R harness connector E8.
2.
Check harness continuity between IPDM E/R terminal 40 and ECM terminal 113.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 13.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E11, F2
●
Harness for open or short between IPDM E/R and ECM
>> Repair harness or connectors.
5.
CHECK CONDENSER POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
Disconnect condenser harness connector.
4.
Turn ignition switch ON.
5.
Check voltage between condenser terminal 1 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 6.
6.
CHECK 15A FUSE
1.
Turn ignition switch OFF.
2.
Disconnect 15A fuse.
3.
Check 15A fuse.
OK or NG
OK
>> GO TO 7.
NG
>> Replace fuse.
Continuity should exist.
Voltage:
Battery voltage should exist for 1 sec-
ond after ignition switch is turned ON.
PBIB0624E
FUEL PUMP
EC-663
C
D
E
F
G
H
I
J
K
L
M
A
EC
7.
CHECK CONDENSER POWER SUPPLY CIRCUIT-II
1.
Disconnect IPDM E/R harness connector E8.
2.
Check harness continuity between IPDM E/R terminal 39 and condenser terminal 1.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 13.
NG
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E123, B41
●
Harness for open or short between IPDM E/R and condenser
>> Repair harness or connectors.
9.
CHECK CONDENSER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check harness continuity between condenser terminal 2 and ground.
Refer to Wiring Diagram.
3.
Also check harness for short to power.
OK or NG
OK
>> GO TO 10.
NG
>> Repair open circuit or short to power in harness or connectors.
10.
CHECK CONDENSER
Refer to
EC-664, "Component Inspection"
OK or NG
OK
>> GO TO 11.
NG
>> Replace condenser.
11.
CHECK FUEL PUMP POWER SUPPLY AND GROUND CIRCUIT FOR OPEN AND SHORT
1.
Disconnect “fuel level sensor unit and fuel pump” harness con-
nector.
2.
Disconnect harness connectors E123, B41
3.
Check harness continuity between the following;
“fuel level sensor unit and fuel pump” terminal 1 and harness
connector B41 terminal 3,
“fuel level sensor unit and fuel pump” terminal 3 and ground.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 12.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
Continuity should exist.
Continuity should exist.
Continuity should exist.
PBIB1280E
EC-664
FUEL PUMP
12.
CHECK FUEL PUMP
Refer to
EC-664, "Component Inspection"
OK or NG
OK
>> GO TO 13.
NG
>> Replace “fuel level sensor unit and fuel pump”.
13.
CHECK INTERMITTENT INCIDENT
Refer to
EC-151, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair or replace harness or connectors.
Component Inspection
NBS0011X
FUEL PUMP
1.
Disconnect “fuel level sensor unit and fuel pump” harness connector.
2.
Check resistance between “fuel level sensor unit and fuel pump”
terminals 1 and 3.
CONDENSER
1.
Turn ignition switch OFF.
2.
Disconnect condenser harness connector.
3.
Check resistance between condenser terminals 1 and 2.
Removal and Installation
NBS0011Y
FUEL PUMP
Refer to
FL-5, "FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY"
Resistance: 0.2 - 5.0
Ω
[at 25
°
C (77
°
F)]
SEC918C
Resistance: Above 1M
Ω
[at 25
°
C (77
°
F)]
PBIB0794E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст