Infiniti G35 (V35). Manual — part 203
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-199
C
D
E
F
G
H
J
K
L
M
A
B
BL
Terminals and Reference Value of BCM
NIS001IU
Terminal Wire
color
Item
Condition
Voltage (V)
(Approx.)
11
LG
Power supply (ACC)
Ignition switch (ACC or ON posi-
tion)
Battery voltage
12
P
Front door switch
(passenger side)
Passenger side
door
ON (door Open)
0
OFF (door
closed)
18*
B
sensor ground
—
0
19*
Y
Remote keyless entry receiver
power supply
Ignition switch
is removed
from key cylin-
der
Waiting state
Any operation
using keyfob
20*
L
Remote keyless entry receiver
signal
Ignition switch
is removed
from key cylin-
der
Waiting state
Any operation
using keyfob
22
Y
Power window serial link
Ignition switch ON or power win-
dow timer operating
23
G/OR
Security indicator lamp
Goes off
→
Illuminates
Battery voltage
→
0
39
L
CAN-H
—
—
40
P
CAN-L
—
—
42
GY
Battery power supply (fuse)
—
Battery voltage
SKIB3419J
OCC3881D
OCC3882D
OCC3879D
OCC3880D
PIIA2344J
BL-200
VEHICLE SECURITY (THEFT WARNING) SYSTEM
*: Without Intelligent Key
Terminals and Reference Value of IPDM E/R
NIS001IV
52
B
Ground
—
0
55
W/R
Battery power supply (fusible
link)
—
Battery voltage
57
R
Trunk room lamp switch signal
ON (Open)
→
OFF (Closed)
0
→
Battery voltage
62
Y
Driver side door switch
ON (Open)
→
OFF (Closed)
ON (door open)
0
OFF (door
closed)
Terminal Wire
color
Item
Condition
Voltage (V)
(Approx.)
SKIB3419J
Terminal Wire
color
Item
Condition
Voltage (V)
(Approx.)
38
B/R
Ground (power)
—
0
48
L
CAN-H
—
—
49
P
CAN-L
—
—
51
G/B
Horn relay control signal
Panic alarm is operating
0
Other than above
Battery voltage
56
LG/B
Hood switch signal
ON (Open)
→
OFF (closed)
0
→
Battery voltage
60
B/R
Ground (signal)
—
0
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-201
C
D
E
F
G
H
J
K
L
M
A
B
BL
CONSULT-II Inspection Procedure
NIS001IW
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-LL START PROCEDURE
Refer to
GI-37, "CONSULT-II Start Procedure"
.
CONSULT-II APPLICATION ITEMS
Work Support
Data Monitor
Active Test
BCM diagnosis
position
Inspection items and diagnosis mode
Description
THEFT ALM
DATA MONITOR
Displays the input data to BCM in real time basis.
ACTIVE TEST
Gives a drive signal to a load to check the operation.
WORK SUPPORT
Changes setting of each function.
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR”
on CONSULT-II screen.
Monitored Item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
I-KEY LOCK
Indicates [ON/OFF] condition of lock signal from key fob.
I-KEY UNLOCK
Indicates [ON/OFF] condition of unlock signal from key fob.
I-KEY TRUNK
Indicates [ON/OFF] condition of trunk opener signal from key fob.
TRUNK OPNR SW
This is displayed even when it is not equipped.
TRUNK CYL SW
This is displayed even when it is not equipped.
TRUNK OPN MNTR
Indicates [ON/OFF] condition of trunk room lamp switch.
HOOD SW
Indicates [ON/OFF] condition of hood switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
This is displayed even when it is not equipped.
DOOR SW-RL
This is displayed even when it is not equipped.
BACK DOOR SW
This is displayed even when it is not equipped.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-II screen is touched.
VEHICLE SECURITY HORN
This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-II screen is touched.
HEADLAMP(HI)
This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5
seconds after “ON” on CONSULT-II screen is touched.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст