Infiniti G35 (V35). Manual — part 1
ACC-1
ACCELERATOR CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
ACC
ACCELERATOR CONTROL SYSTEM
PRECAUTIONS . . . . . . . . . . . . . . .. 2
ACCELERATOR CONTROL SYSTEM . . . . . .. 3
Components . . . . . . . . . . . . . . . . 3
Removal and Installation . . . . . . . . . . .. 3
ACC-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NBS00137
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery Service
NBS00138
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
ACCELERATOR CONTROL SYSTEM
ACC-3
C
D
E
F
G
H
I
J
K
L
M
A
ACC
ACCELERATOR CONTROL SYSTEM
PFP:18005
Components
NBS00139
Removal and Installation
NBS0013A
REMOVAL
1.
Disconnect accelerator pedal position sensor harness connector.
2.
Loosen nuts, and remove accelerator pedal assembly.
CAUTION:
●
Do not disassemble accelerator pedal assembly. Do not remove accelerator pedal position sen-
sor from accelerator pedal assembly.
●
Avoid impact from dropping etc. during handling.
●
Be careful to keep accelerator pedal assembly away from water.
INSTALLATION
Install in the reverse order of removal.
INSPECTION AFTER INSTALLATION
●
Make sure that accelerator pedal moves smoothly within the whole operation range.
●
Make sure that accelerator pedal securely returns to the original position.
●
For the electrical inspection of accelerator pedal position sensor. Refer to
EC-599, "DTC P2127, P2128 APP SENSOR"
and
CAUTION:
When harness connector of accelerator pedal position sensor is disconnected, perform “Acceler-
ator Pedal Released Position Learning”. Refer to
EC-79, "Accelerator Pedal Released Position
1.
Accelerator pedal assembly
PBIC2080E
ACC-4
ACCELERATOR CONTROL SYSTEM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст