Infiniti G35 (V35). Manual — part 739
SE-58
AUTOMATIC DRIVE POSITIONER
2.
CHECK DOOR SWITCH (DRIVER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect door switch connector.
3.
Check continuity between door switch connector and ground part of door switch.
OK or NG
OK
>> GO TO 3.
NG
>> Replace door switch (driver side).
3.
CHECK DOOR SWITCH (DRIVER SIDE) HARNESS CONTINUITY
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector B4 terminal 62 and
door switch connector B17 terminal 1.
3.
Check continuity between BCM connector B4 terminal 62 and
ground.
OK or NG
OK
>> Door switch (driver side) circuit is OK.
NG
>> Repair or replace harness between BCM and door
switch (driver side).
Terminals
Door switch
Continuity
1
Ground part of
door switch
Pushed
No
Released
Yes
PIIA5091E
62 (Y) – 1 (G/B)
: Continuity should exist.
62 (Y) – Ground
: Continuity should not exist.
PIIA5090E
AUTOMATIC DRIVE POSITIONER
SE-59
C
D
E
F
G
H
J
K
L
M
A
B
SE
Check Sliding Switch Circuit
NIS001I1
1.
CHECK FUNCTION
With CONSULT-II
With “SLIDE SW-FR, SLIDE SW-RR” on the DATA MONITOR, operate the sliding switch to check ON/OFF
operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Sliding switch operate, check voltage between driver seat control unit connector and ground.
OK or NG
OK
>> Sliding switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch connector.
2.
Check continuity between driver seat control unit connector
B352 terminals 11, 26 and power seat switch connector B355
terminals 11, 26.
3.
Check continuity between driver seat control unit connector
B352 terminals 11, 26 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and power seat switch.
Monitor item
[OPERATION or UNIT]
Contents
SLIDE SW – FR
“ON/
OFF”
ON/OFF status judged from the sliding switch
(FR) signal is displayed.
SLIDE SW – RR
“ON/
OFF”
ON/OFF status judged from the sliding switch
(RR) signal is displayed.
PIIB2055E
Connector
Terminals
(Wire color)
Sliding switch condition
Voltage (V)
(Approx.)
(+)
(-)
B352
26 (Y)
Ground
FORWARD
0
Other than above
Battery voltage
11 (BR)
BACKWARD
0
Other than above
Battery voltage
PIIA4577E
11 (BR) – 11 (BR)
: Continuity should exist.
26 (Y) – 26 (Y)
: Continuity should exist.
11 (BR) – Ground
: Continuity should not exist.
26 (Y) – Ground
: Continuity should not exist.
PIIB4195E
SE-60
AUTOMATIC DRIVE POSITIONER
3.
CHECK SLIDING SWITCH
Check continuity between power seat switch as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch.
Check Reclining Switch
NIS001I2
1.
CHECK FUNCTION
With CONSULT-II
With “RECLINING SW-FR, RECLINING SW-RR” on the DATA MONITOR, operate the reclining switch to
check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Reclining switch operate, check voltage between driver seat control unit connector and ground.
OK or NG
OK
>> Reclining switch is OK.
NG
>> GO TO 2.
Terminal
Sliding switch condition
Continuity
26
32D
FORWARD
Yes
Other than above
No
11
BACKWARD
Yes
Other than above
No
PIIB4196E
Monitor item
[OPERATION or UNIT]
Contents
RECLN SW – FR
“ON/
OFF”
ON/OFF status judged from the reclining switch
(FR) signal is displayed.
RECLN SW – RR
“ON/
OFF”
ON/OFF status judged from the reclining switch
(RR) signal is displayed.
PIIB2056E
Connector
Terminals
(Wire color)
Reclining switch
condition
Voltage (V)
(Approx.)
(+)
(–)
B352
27 (R/G)
Ground
FORWARD
0
Other than above
Battery voltage
12 (SB)
BACKWARD
0
Other than above
Battery voltage
PIIA4580E
AUTOMATIC DRIVE POSITIONER
SE-61
C
D
E
F
G
H
J
K
L
M
A
B
SE
2.
CHECK HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch connector.
2.
Check continuity between driver seat control unit connector
B352 terminals 12, 27 and power seat switch connector B355
terminals 12, 27.
3.
Check continuity between driver seat control unit connector
B352 terminals 12, 27 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness between driver seat control unit and power seat switch.
3.
CHECK RECLINING SWITCH
Check continuity between power seat switch as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch.
12 (SB) – 12 (SB)
: Continuity should exist.
27 (R/G) – 27 (R/G)
: Continuity should exist.
12 (SB) – Ground
: Continuity should not exist.
27 (R/G) – Ground
: Continuity should not exist.
PIIB4197E
Terminal
Reclining switch condition
Continuity
27
32D
FORWARD
Yes
Other than above
No
12
BACKWARD
Yes
Other than above
No
PIIB4198E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст