Infiniti G35 (V35). Manual — part 697
RFD-14
FRONT OIL SEAL
c.
Put a suitable drift on the center of side flange, then drive it until
sound changes.
NOTE:
When installation is completed, driving sound of the side flange
turns into a sound which seems to affect the whole final drive.
d.
Confirm that the dimension of the side flange installation (Mea-
surement A) in the figure comes into the following.
9.
Install drive shaft. Refer to
RAX-10, "Removal and Installation"
.
10. Install rear wheel sensor. Refer to
.
11. Refill gear oil to the final drive and check oil level. Refer to
.
12. Check the final drive for oil leakage. Refer to
Measurement A: 326 – 328 mm (12.83 – 12.91 in)
PDIA0631E
SIDE OIL SEAL
RFD-15
C
E
F
G
H
I
J
K
L
M
A
B
RFD
SIDE OIL SEAL
PFP:33142
Removal and Installation
NDS0001N
REMOVAL
1.
Remove rear wheel sensor. Refer to
.
2.
Remove drive shaft from final drive. Then suspend it by wire etc. Refer to
RAX-10, "Removal and Installa-
3.
Install attachment to side flange, and then pull out the side
flange with the sliding hammer.
NOTE:
4.
Remove side oil seal, using a flat-bladed screwdriver.
CAUTION:
Be careful not to damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to side oil seal lips.
2.
Install side oil seal until it becomes flush with the case end,
using the drift.
CAUTION:
●
Do not reuse oil seal.
●
When installing, do not incline oil seal.
3.
Install side flange with the following procedure.
NOTE:
Install the RH side flange, then install the LH side flange. If LH
side flange is installed first, the RH side flange comes out some-
times from the shock of installing the RH side flange. [For
R200V (with LSD)]
a.
Attach the protector to side oil seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
Tool number
A: KV40104100 (
—
)
B: ST36230000 (J-25840-A)
Model
Circular clip installation position
Right side
Left side
R200 (2-pinion)
Final drive side
R200V (LSD)
Final drive side
Side flange side
SDIA1005E
SDIA0495E
Tool number
: KV38100200 (J-26233)
Tool number
: KV38107900 (J-39352)
SDIA0496E
SDIA0822E
RFD-16
SIDE OIL SEAL
c.
Put a suitable drift on the center of side flange, then drive it until
sound changes.
NOTE:
When installation is completed, driving sound of the side flange
turns into a sound which seems to affect the whole final drive.
d.
Confirm that the dimension of the side flange installation (Mea-
surement A) in the figure comes into the following.
4.
Install drive shaft. Refer to
RAX-10, "Removal and Installation"
.
5.
Install rear wheel sensor. Refer to
.
Measurement A: 326 – 328 mm (12.83 – 12.91 in)
PDIA0631E
REAR FINAL DRIVE ASSEMBLY
RFD-17
C
E
F
G
H
I
J
K
L
M
A
B
RFD
REAR FINAL DRIVE ASSEMBLY
PFP:38300
Removal and Installation
NDS0001O
COMPONENTS
REMOVAL
1.
Remove exhaust center tube with a power tool. Refer to
EX-3, "Removal and Installation"
2.
Remove rear stabilizer bar with a power tool. Refer to
RSU-16, "Removal and Installation"
3.
Remove propeller shaft from the final drive. Refer to
PR-4, "Removal and Installation"
.
4.
Remove drive shaft from final drive. Then suspend it by wire etc.
Refer to
RAX-10, "Removal and Installation"
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
1.
Rear final drive assembly
2.
Upper stopper
3.
Propeller shaft
4.
Washer
5.
Lower stopper
6.
Drive shaft
SDIA3057E
SDIA1094E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст