Infiniti G35 (V35). Manual — part 233
REAR DISC BRAKE
BR-27
C
D
E
G
H
I
J
K
L
M
A
B
BR
REAR DISC BRAKE
PFP:44000
On-Vehicle Inspection
NFS000K0
PAD WEAR INSPECTION
●
Inspect the thickness from an inspection hole on cylinder body.
Use a scale for inspection if necessary.
Components
NFS000K1
Standard thickness
: 8.5 mm (0.335 in)
Repair limit thickness
: 2.0 mm (0.079 in)
BRA0010D
1.
Union bolt
2.
Brake hose
3.
Copper washer
4.
Cap
5.
Bleed valve
6.
Sliding pin bolt
7.
Cylinder body
8.
Piston seal
9.
Piston
10.
Piston boot
11.
Retaining ring
12.
Inner shim cover
13.
Inner shim
14. Inner pad
15.
Pad retainer
16.
Outer pad
17. Outer shim
18.
Slide pin boot
19.
Torque member mounting bolt
20. Bushing
21.
Torque member
Refer to
and the followings for the symbols in the figure.
1: Apply rubber grease.
2: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
PFIA0686E
BR-28
REAR DISC BRAKE
WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of airborne
particles or other materials.
CAUTION:
●
While removing cylinder body, never depress the brake pedal because the piston will pop out.
●
It is not necessary to remove torque member mounting bolts on torque member and brake hose
except for disassembly or replacement of the caliper assembly. In this case, hang cylinder body
with a wire so as not to stretch brake hose.
●
Do not damage piston boot.
●
If any shim is subject to serious corrosion, replace it with a new one.
●
Always replace shims and shim cover as a set when replacing brake pads.
●
Keep the rotor clean of brake fluid.
●
Burnish the brake pads and disc rotor mutually contacting surfaces after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to
.
Removal and Installation of Brake Pad
NFS000K2
REMOVAL
1.
Remove tires from vehicle with a power tool.
2.
Remove sliding pin bold (one on top).
3.
Hang cylinder body with a wire, and remove pads, shims, shim cover and pad retainers from torque mem-
ber.
INSTALLATION
1.
Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the rear of the pad and to both sides
of the shim, and install the inner shim and shim cover to the inner pad, and the outer shim to the outer
pad.
2.
Install the pad retainer and pad assemblies to the torque member.
3.
Push the piston in so that the pad is firmly installed, and install cylinder body to torque member.
CAUTION:
When replacing pads with new ones, press in piston until pads can be installed. In this case, care-
fully monitor brake fluid level in reservoir tank because brake fluid will return to master cylinder
reservoir tank.
NOTE:
Use a disc brake piston tool (commercial service tool) to easily press piston.
4.
Install the sliding pin bolt (one on top) and tighten to the specified torque. Refer to
.
5.
Secure disc rotor with wheel nuts. Depress brake pedal a few times until it gets a responsive touch.
6.
Check brake for drag.
7.
Install tires to vehicle.
Removal and Installation of Caliper Assembly
NFS000K3
REMOVAL
1.
Remove tires from vehicle with a power tool.
2.
Fasten disc rotor using wheel nut.
3.
Drain brake fluid. Refer to
.
4.
Remove union bolt and then remove brake hose from caliper
assembly.
5.
Remove torque member mounting bolts, and remove caliper
assembly.
CAUTION:
Do not drop brake pad.
6.
Remove disc rotor.
3: Apply polyglycol ether based lubricant.
: Apply brake fluid.
PFIA0292J
REAR DISC BRAKE
BR-29
C
D
E
G
H
I
J
K
L
M
A
B
BR
CAUTION:
Put matching marks on wheel hub assembly and disc rotor, if it necessary to remove disc rotor.
INSTALLATION
CAUTION:
●
Refill with new brake fluid “DOT 3”.
●
Never reuse drained brake fluid.
1.
Install disc rotor.
CAUTION:
Matching marks of disc rotor and wheel hub put at the time of removal when reusing disc rotor.
2.
Install caliper assembly to the vehicle, and tighten torque member mounting bolts to the specified torque.
Refer to
CAUTION:
Before installing caliper assembly to the vehicle, wipe off oil and grease on washer seats on steer-
ing knuckle and mounting surface of caliper assembly.
3.
Install L shape pin of brake hose to caliper assembly and tighten union bolts to the specified torque. Refer
to
CAUTION:
●
Do not reuse the copper washer for union bolts.
●
Securely attach brake hose to protrusion on caliper assembly.
4.
Insert new brake fluid and bleed air. Refer to
BR-10, "Bleeding Brake System"
5.
Check brake for drag.
6.
Install tires to vehicle.
Disassembly and Assembly of Caliper Assembly
NFS000K4
NOTE:
Do not remove torque member, pads, shims, shim cover and pad retainers when disassembling and assem-
bling cylinder body.
DISASSEMBLY
1.
Remove the slide pin bolt, and then remove cylinder body from torque member.
CAUTION:
Do not drop pads, shims, shim cover and pad retainer from torque member.
2.
Remove sliding pin boot from torque member.
3.
As shown in the figure, using a flat-bladed screwdriver, remove
the retaining ring from the cylinder body.
SBR028A
BR-30
REAR DISC BRAKE
4.
Place a wooden block as shown in the figure, and blow air from
union bolt mounting hole to remove pistons and piston boots.
CAUTION:
Do not get fingers caught in the piston.
5.
Using a flat-bladed screwdriver, remove piston seals from cylin-
der body.
CAUTION:
Be careful not to damage cylinder inner wall.
INSPECTION AFTER DISASSEMBLY
Cylinder Body
CAUTION:
Use new brake fluid to clean. Never use mineral oils such as gasoline or kerosene.
●
Check inner wall of cylinder for corrosion, wear, and damage. If a malfunction is detected, replace cylinder
body.
●
Minor flaws caused by corrosion or a foreign material can be removed by polishing a surface of inner wall
with a fine sandpaper. Replace the cylinder body, if a malfunction is detected.
Torque Member
Check for wear, cracks, and damage. If a malfunction is detected, replace the affected part.
Piston
CAUTION:
The piston sliding surface is plated. Do not polish with sandpaper.
Check piston surface for corrosion, wear, and damage. If a malfunction is detected, replace applicable part.
Sliding Pin Bolts and Sliding Pin Boots
Check sliding pin bolts and sliding pin boots for wear, damage, and cracks. If a malfunction is detected,
replace applicable part.
ASSEMBLY
1.
Apply polyglycol ether based lubricant to the piston seal, and
install them to the cylinder body.
CAUTION:
Do not reuse piston seal.
BRD0041D
SFIA0999E
SFIA2278E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст