Infiniti G35 (V35). Manual — part 455
FRONT BUMPER
EI-15
C
D
E
F
G
H
J
K
L
M
A
B
EI
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1.
Remove bumper clips, front grille clips, and remove front grille. Refer to
2.
Remove screws of front air spoiler and remove front air spoiler.
3.
Remove bolts on lower side of bumper.
4.
Remove screws and clips of both right/left fender protectors on front side. Refer to
.
5.
Remove screws of both right/left fender.
6.
Disconnect front side marker lamp harness connector.
7.
Remove bumper fascia assembly.
8.
Remove energy absorber.
9.
Remove bolts and nuts of bumper reinforcement and remove bumper reinforcement.
10. Remove bolts and clips of bumper stay and remove bumper stay.
11. Remove front side marker lamp located in bumper fascia. Refer to
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, adjust the clearance.
Portion
Clearance
Front bumper – Front grille
A – A
1.0 – 3.0 mm (0.039 – 0.118 in)
Front bumper – Hood
B – B
3.0 – 7.0 mm (0.118 – 0.276 in)
Front bumper – Headlamp
C – C
2.5 – 5.5 mm (0.098 – 0.217 in)
Front bumper – Headlamp
D – D
1.5 – 4.5 mm (0.059 – 0.177 in)
Front bumper – Front fender
E – E
0.0 – 0.5 mm (0.000 – 0.020 in)
EI-16
REAR BUMPER
REAR BUMPER
PFP:H5022
Removal and Installation
NIS000GN
1.
Bumper stay
2.
Energy absorber (rear)
3.
Bumper reinforcement
4.
Energy absorber (front)
5.
Bumper fascia assembly
6.
Bumper retainer (lower)
7.
Bumper over-rider
8.
Bumper clamp
PIIB9167E
REAR BUMPER
EI-17
C
D
E
F
G
H
J
K
L
M
A
B
EI
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1.
EI-38, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
.
2.
Remove rear combination lamp assembly. Refer to
LT-126, "Removal and Installation"
.
3.
Remove bumper fascia bolts from both right/left rear fender.
4.
Remove bumper fascia clips of upper portion, and remove screw of lower portion.
5.
Pull out center of bumper fascia, and remove bumper fascia from clips.
6.
Disconnect license lamp harness connector and remove bumper fascia assembly.
7.
Remove energy absorber (front).
8.
Remove reinforcement bolts/nuts and remove reinforcement assembly.
9.
Remove bumper stay bolts and remove bumper stay.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, adjust the clearance.
Portion
Clearance
Rear bumper – Rear fender
A – A
0.0 – 0.5 mm (0.000 – 0.020 in)
Rear bumper – Rear fender
B – B
0.0 – 0.5 mm (0.000 – 0.020 in)
Rear bumper – Rear combination lamp
C – C
1.0 – 4.0 mm (0.039 – 0.157 in)
Rear bumper – Trunk lid
D – D
4.0 – 8.0 mm (0.157 – 0.315 in)
EI-18
FRONT GRILLE
FRONT GRILLE
PFP:62310
Removal and Installation
NIS000GO
REMOVAL
1.
Apply protection tape around outer circumference of front grille (bumper fascia side).
2.
Remove clips on upper side of grille.
3.
Pull down tips of four turn fasteners from rear side of grille.
4.
Disconnect turn fasteners then pull out grille.
INSTALLATION
Install in the reverse order of removal.
PIIA3565E
1.
Front grille
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст