Infiniti G35 (V35). Manual — part 602
LT-88
TURN SIGNAL AND HAZARD WARNING LAMPS
3.
ACTIVE TEST
With CONSULT-II
1.
Select “BCM” on CONSULT-II. Select “FLASHER” active test.
Refer to
.
2.
Touch “RH” or “LH” screen.
3.
Make sure turn signal lamp RH and LH operates.
Without CONSULT-II
GO TO 4.
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
NG
>> GO TO 4.
4.
CHECK SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and all turn signal lamp connectors.
3.
Check continuity (short circuit) between BCM harness connector
and ground.
OK or NG
OK
>> Replace BCM if turn signal lamps does not work after
setting the connector again. Refer to
BCS-16, "Removal and Installation of BCM"
.
NG
>> Repair harness or connector.
Turn signal lamp should operate.
PKIA7749E
BCM
connector
Terminal
Ground
Continuity
RH
M2
46
No
LH
45
PKIA6289E
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-89
C
D
E
F
G
H
I
J
L
M
A
B
LT
Hazard Warning Lamp Does Not Operate But Turn Signal Lamp Operates
NKS002OX
1.
CHECK HAZARD SWITCH INPUT SIGNAL
With CONSULT-II
Select “BCM” on CONSULT-II. With “FLASHER” data monitor, make
sure “HAZARD SW” turns ON-OFF linked with operation of hazard
switch.
Without CONSULT-II
Check voltage between BCM harness connector and ground.
OK or NG
OK
>> Replace BCM. Refer to
BCS-16, "Removal and Installa-
NG
>> GO TO 2.
2.
CHECK HAZARD SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and hazard switch connector.
3.
Check continuity BCM harness connector M1 terminal 29 and
hazard switch harness connector M282
*1
, M46
*2
terminal 2.
*1: with A/T, *2: with M/T
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK HAZARD SWITCH GROUND
Check continuity hazard switch harness connector M282
*1
, M46
*2
terminal 1 and ground.
*1: with A/T, *2: with M/T
OK or NG
OK
>> GO TO 4.
NG
>> Repair harness or connector.
When hazard switch is ON
position
: HAZARD SW ON
PKIA7601E
(+)
(
−
)
Condition
Voltage
BCM
connector
Terminal
M1
29
Ground
Hazard switch is ON
Approx. 0 V
Hazard switch is OFF
Battery voltage
PKIB6809E
29 – 2
: Continuity should exist.
PKIA7018E
1 – Ground
: Continuity should exist.
SKIA8972E
LT-90
TURN SIGNAL AND HAZARD WARNING LAMPS
4.
CHECK HAZARD SWITCH
1.
Disconnect hazard switch connector.
2.
Check continuity hazard switch terminals.
OK or NG
OK
>> Replace BCM if turn signal lamps does not work after
setting the connector again. Refer to
.
NG
>> Replace hazard switch.
Bulb Replacement
NKS002OZ
FRONT TURN SIGNAL LAMP
Refer to
REAR TURN SIGNAL LAMP
Refer to
.
Removal and Installation
NKS002P0
FRONT TURN SIGNAL LAMP
Refer to
LT-32, "Removal and Installation"
.
REAR TURN SIGNAL LAMP
Refer to
LT-126, "Removal and Installation"
.
Hazard switch
Condition
Continuity
Terminal
1
2
Hazard switch is ON
Yes
Hazard switch is OFF
No
PKIA4601E
LIGHTING AND TURN SIGNAL SWITCH
LT-91
C
D
E
F
G
H
I
J
L
M
A
B
LT
LIGHTING AND TURN SIGNAL SWITCH
PFP:25540
Removal and Installation
NKS000ID
REMOVAL
1.
Remove steering column cover. Refer to
2.
Remove mounting bolts of cluster lid A and combination meter.
Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
3.
While pressing pawls in direction as shown in the figure, pull
lighting and turn signal switch toward driver door and disconnect
from the base.
4.
Disconnect lighting and turn signal switch connector.
INSTALLATION
Installation is the reverse order of removal.
PKIB6102E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст