Infiniti G35 (V35). Manual — part 686
RAX-16
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Wheel Bearing
NDS00028
Drive Shaft
NDS00029
Axial end play
0 mm (0 in)
Rotational torque
At a load of 49,033 N (5,000 kg, 11,000 lb)
Less than 1.88 N·m (0.19 kg-m, 17 in-lb)
Measurement of spring balance
Less than 18.5 N (1.89 kg, 4.16 lb)
Joint
Wheel side
Final drive side
Grease quantity
86 – 96 g (3.03 – 3.39 oz)
124 – 134 g (4.37 – 4.73 oz)
Boots installed length
97.0 mm (3.819 in)
93.9 mm (3.697 in)
RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
RF
ROOF
PRECAUTIONS . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 4
Work Flow . . . . . . . . . . . . . . . . 4
Generic Squeak and Rattle Troubleshooting . . ... 6
Diagnostic Worksheet . . . . . . . . . . . .. 8
SUNROOF . . . . . . . . . . . . . . . . 10
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . 10
GAP ADJUSTMENT AND HEIGHT DIFFER-
ENCE ADJUSTMENT . . . . . . . . . . . 24
RF-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS000FN
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Battery Service
NIS000FO
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Precautions
NIS000FP
●
Disconnect both battery cables in advance.
●
Do not tamper with or force air bag lid open, as this may adversely affect air bag performance.
●
Be careful not to scratch pad and other parts.
●
When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
●
When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
●
Keep removed parts protected with cloth.
●
If a clip is deformed or damaged, replace it.
●
If an unreusable part is removed, replace it with a new one.
●
Tighten bolts and nuts firmly to the specified torque.
●
After re-assembly has been completed, make sure each part functions correctly.
●
Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
●
Do not use any organic solvent, such as thinner or benzine.
PREPARATION
RF-3
C
D
E
F
G
H
J
K
L
M
A
B
RF
PREPARATION
PFP:00002
Special Service Tools
NIS000FQ
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
NIS000FR
Tool number
(Kent-Moore No.)
Tool name
Description
(J39570)
Chassis ear
Locating the noise
(J43980)
NISSAN Squeak and
Rattle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
(J39565)
Engine ear
Locating the noise
SIIA0995E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст