Infiniti G35 (V35). Manual — part 588
LT-32
HEADLAMP - XENON TYPE -
Removal and Installation
NKS002O2
REMOVAL
1.
Open the driver and front passenger window, and then discon-
nect the battery cable from the negative terminal or remove
power fuse.
CAUTION:
After battery cables are disconnected, never open/close the
driver and/or front passenger door with the window in the
full up position. The automatic window adjusting function
will not work and the side roof panel may be damaged.
2.
Remove front grille. Refer to
3.
Remove front undercover and fender protector. Refer to
.
4.
Remove mounting clip on top of front bumper and screws on
side of front bumper. Refer to
.
5.
Pull side of front bumper toward the vehicle front and disengage
it from clips on the body.
6.
Remove headlamp mounting bolts.
7.
Pull headlamp toward the vehicle front, disconnect connector,
and remove headlamp.
CAUTION:
When removing headlamps, put a shop cloth or something
similar between headlamps and bumper to protect bumper.
INSTALLATION
Installation is the reverse order of removal.
PKIA2392E
PKIA2393E
Headlamp mounting bolt
: 5.9 N·m (0.60 kg-m, 52 in-lb)
HEADLAMP - XENON TYPE -
LT-33
C
D
E
F
G
H
I
J
L
M
A
B
LT
Disassembly
NKS002O3
1.
Turn the plastic cap (high/low) counterclockwise and remove it.
2.
Disconnect the high beam solenoid connector.
3.
Turn the xenon bulb socket counterclockwise and remove it.
4.
Unlock the retaining spring and remove the xenon bulb (high/low).
5.
Disconnect the HID C/U connector.
6.
Remove the mounting screws from the HID C/U.
7.
Disconnect the HID connector and remove a screw from the HID C/U.
8.
Turn the plastic cap (front fog) counterclockwise and remove it.
9.
Disconnect the halogen bulb power supply harness and halogen bulb ground harness from the halogen
bulb (front fog).
10. Unlock the retaining spring and remove the halogen bulb (front fog).
11. Push the claw of the parking lamp bulb socket and remove it.
12. Remove the parking lamp bulb from its socket.
13. Turn the front turn signal lamp bulb socket counterclockwise and remove it.
14. Remove the front turn signal lamp bulb from its socket.
15. Remove the headlamp assembly connector.
1.
High beam solenoid connector
2.
Xenon bulb (high/low)
3.
Seal packing
4.
Plastic cap (high/low)
5.
Xenon bulb socket
6.
Halogen bulb (front fog)
7.
Halogen bulb power supply harness 8.
Halogen bulb ground harness
9.
Seal packing
10. Plastic cap (front fog)
11. Parking lamp bulb
12.
Parking lamp bulb socket
13. Headlamp assembly connector
14. Front turn signal lamp bulb socket
15.
Front turn signal lamp bulb
16. HID C/U connector
17. Screw
18.
HID C/U
19. Seal packing
20. HID connector
21.
Screw
22. Headlamp housing assembly
PKIC5942E
LT-34
HEADLAMP - XENON TYPE -
Assembly
NKS002O4
Assembly is the reverse order of disassembly.
CAUTION:
●
When HID control unit is removed, reinstall it securely and avoid any looseness.
●
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
Servicing to Replace Headlamps When Damaged
NKS002O5
If only installation part as shown in the figure is damaged, and head-
lamp housing itself is not damaged, repair can be completed easily
by installing correction brackets.
REMOVAL AND INSTALLATION
1.
Remove headlamps. Refer to
LT-32, "Removal and Installation"
.
2.
Cut damaged section of installation part, and then shape with
sandpaper.
3.
Attach Inner side bracket to headlamp housing boss with 2
screws.
HID control unit
: 3.2 N·m (0.33 kg-m, 28 in-lb)
PKIC5943E
PKIC5944E
DAYTIME LIGHT SYSTEM
LT-35
C
D
E
F
G
H
I
J
L
M
A
B
LT
DAYTIME LIGHT SYSTEM
PFP:284B2
Component Parts and Harness Connector Location
NKS0027G
System Description
NKS0027H
Daytime light system turns ON daytime light lamps (front fog lamps) while driving. Daytime light lamps are not
turned ON if engine is activated with parking brake ON. Release parking brake to turn on daytime light lamps.
The lamps turn OFF when lighting switch is in the 2ND position or AUTO position (headlamp is ON) and when
lighting switch is in the PASSING position. (Daytime light lamps are not turned off only by parking brake itself.)
A parking brake signal and engine run or stop signal are sent to BCM (body control module) by CAN commu-
nication line, and control daytime light system.
OUTLINE
Power is supplied at all times
●
to ignition relay located in IPDM E/R (intelligent power distribution module engine room), from battery
direct,
PKIC5973E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст