Infiniti G35 (V35). Manual — part 274
WARNING CHIME
DI-43
C
D
E
F
G
H
I
J
L
M
A
B
DI
TKWM2169E
DI-44
WARNING CHIME
Terminals and Reference Values for BCM
NKS004R8
CAUTION:
●
Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal and wiper switch OFF not to be fluctuated by overloaded.
●
Turn wiper dial position to 4 except when checking waveform or voltage of wiper dial position.
Wiper dial position can be confirmed on CONSULT-II. Refer to
Ter-
minal
No.
Wire
color
Signal name
Measuring condition
Reference value
Ignition
switch
Operation or condition
2
G/R
Combination
switch input 5
ON
Lighting, turn,
wiper switch
(Wiper intermit-
tent dial position 4)
OFF
Approx. 0 V
Lighting switch 1ST
Approx. 1.0 V
33
L
Combination
switch output 4
ON
Lighting, turn,
wiper switch
(Wiper intermit-
tent dial position 4)
OFF
Approx. 7.2 V
Lighting switch 1ST
Approx. 1.2 V
37
B/P
Key switch sig-
nal
OFF
Key is removed
Approx. 0 V
Key is inserted
Approx. 12 V
38
W/L
Ignition switch
(ON)
ON
—
Battery voltage
39
L
CAN
−
H
—
—
—
40
P
CAN
−
L
—
—
—
42
GY
Battery power
supply
OFF
—
Battery voltage
52
B
Ground
ON
—
Approx. 0 V
55
W/R
Battery power
supply
OFF
—
Battery voltage
62
Y
Driver side
door switch
signal
OFF
Driver's door
ON (open)
Approx. 0 V
OFF (close)
Approx. 12 V
PKIB4959J
PKIB4960J
PKIB4958J
WARNING CHIME
DI-45
C
D
E
F
G
H
I
J
L
M
A
B
DI
CONSULT-II Function (BCM)
NKS000LK
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
DIAGNOSIS ITEMS DESCRIPTION
CONSULT-II BASIC OPERATION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1.
With the ignition switch OFF, connect “CONSULT-II” and “CON-
SULT-II CONVERTER” to the data link connector, and the turn
the ignition switch ON.
2.
Touch “START (NISSAN BASED VHCL)”.
3.
Touch “BCM” on “SELECT SYSTEM” screen. If “BCM” is not
indicated, go to
GI-38, "CONSULT-II Data Link Connector (DLC)
.
BCM diagnosis position
Diagnosis mode
Description
Reference
page
BUZZER
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending driving
signal to them.
BCM
SELF-DIAG RESULTS
BCM performs self-diagnosis of CAN communication.
PIIA1095E
BCIA0029E
BCIA0030E
DI-46
WARNING CHIME
4.
Touch “BUZZER” or “BCM” on “SELECT TEST ITEM” screen.
5.
Select “DATA MONITOR”, “ACTIVE TEST” or “SELF-DIAG
RESULTS” on “SELECT DIAG MODE” screen.
DATA MONITOR
Operation Procedure
1.
Touch “BUZZER” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch “ALL SIGNALS” or “SELECTION FROM MENU” on “DATA MONITOR” screen.
4.
If “SELECTION FROM MENU” is selected, touch the desired monitor item. If “ALL SIGNALS” is selected,
all items required to control are monitored.
5.
Touch “START”.
6.
During monitoring, touching “RECORD” can start recording the monitored item status.
Display Item List
ACTIVE TEST
Operation Procedure
1.
Touch “BUZZER” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch the item to be tested, and check the operation.
4.
During the operation check, touching “OFF” deactivates the operation.
PKIB1958E
BCIA0031E
ALL SIGNALS
Monitors all items.
SELECTION FROM MENU
Selects and monitors items.
Monitored item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
LIGHT SW 1ST
Indicates [ON/OFF] condition of lighting switch.
BUCKLE SW
Indicates [ON/OFF] condition of seat belt buckle switch (driver side).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст