Infiniti G35 (V35). Manual — part 15
TROUBLE DIAGNOSIS
AT-51
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
While holding down the foot brake, gradually press down the
accelerator pedal.
6.
Quickly read off the stall speed, then quickly remove your foot
from the accelerator pedal.
CAUTION:
Do not hold down the accelerator pedal for more than 5 sec-
onds during this test.
7.
Move the selector lever to the “N” position.
8.
Cool down the ATF.
CAUTION:
Run the engine at idle for at least one minute.
9.
Repeat steps 5 through 8 with selector lever in “R” position.
Judgment Stall Test
O: Stall speed within standard value position
H: Stall speed higher than standard value
L: Stall speed lower than standard value
Stall test standard value position
Stall speed:
2,650 - 2,950 rpm
SAT514G
SCIA6230E
Selector lever position
Expected problem location
“D”, “M”
“R”
Stall speed
H
O
●
Forward brake
●
Forward one-way clutch
●
1st one-way clutch
●
3rd one-way clutch
O
H
●
Reverse brake
L
L
●
Engine and torque converter one-way clutch
H
H
●
Line pressure low
Does not shift up “D”, “M” position 1
→
2
Slipping in 2nd, 3rd or 4th gear
Direct clutch slippage
Does not shift up “D”, “M” position 2
→
3
Slipping in 3rd, 4th or 5th gear
high and low reverse clutch slippage
Does not shift up “D”, “M” position 3
→
4
Slipping in 4th or 5th gear
Input clutch slippage
Does not shift up “D”, “M” position 4
→
5
Slipping in 5th gear
Front brake slippage
AT-52
TROUBLE DIAGNOSIS
LINE PRESSURE TEST
Line Pressure Test Port
Line Pressure Test Procedure
1.
Inspect the amount of engine oil and replenish if necessary.
2.
Drive the car for about 10 minutes to warm it up so that the A/T fluid reaches in range of 50 to 80
°
C (122
to 176
°
F), then inspect the amount of ATF and replenish if necessary.
NOTE:
The A/T fluid temperature rises in range of 50 to 80
°
C (122 to 176
°
F) during 10 minutes of driving.
3.
After warming up remove the oil pressure detection plug and
install the oil pressure gauge [ST2505S001(J-34301-C)].
CAUTION:
When using the oil pressure gauge, be sure to use the O-
ring attached to the oil pressure detection plug.
4.
Securely engage the parking brake so that the tires do not turn.
5.
Start the engine, then measure the line pressure at both idle and
the stall speed.
CAUTION:
●
Keep the brake pedal pressed all the way down during
measurement.
●
When measuring the line pressure at the stall speed,
refer to
6.
After the measurements are complete, install the oil pressure
detection plug and tighten to the specified torque below.
CAUTION:
●
Do not reuse O-ring.
SCIA2187E
SCIA5309E
SCIA7463E
: 7.3 N·m (0.74 kg-m, 65 in-lb)
SAT493G
TROUBLE DIAGNOSIS
AT-53
D
E
F
G
H
I
J
K
L
M
A
B
AT
●
Apply ATF to O-ring.
Line Pressure
Judgment of Line Pressure Test
Engine speed
Line pressure
kPa (kg/cm
2
, psi)
“R” position
“D”, “M” positions
At idle speed
425 - 465 (4.3 - 4.7, 62 - 67)
379 - 428 (3.9 - 4.4, 55 - 62)
At stall speed
1,605 - 1,950 (16.4 - 19.9, 233 - 283)
1,310 - 1,500 (13.4 - 15.3, 190 - 218)
Judgment Possible
cause
Idle speed
Low for all positions
(“P”, “R”, “N”, “D”, “M”)
Possible causes include malfunctions in the pressure supply system and low oil pump output.
For example
●
Oil pump wear
●
Pressure regulator valve or plug sticking or spring fatigue
●
Oil strainer
Þ
oil pump
Þ
pressure regulator valve passage oil leak
●
Engine idle speed too low
Only low for a specific
position
Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
High
Possible causes include a sensor malfunction or malfunction in the line pressure adjustment
function.
For example
●
Accelerator pedal position signal malfunction
●
A/T fluid temperature sensor malfunction
●
Line pressure solenoid malfunction (sticking in OFF state, filter clog, cut line)
●
Pressure regulator valve or plug sticking
Stall speed
Line pressure does
not rise higher than
the line pressure for
idle.
Possible causes include a sensor malfunction or malfunction in the pressure adjustment func-
tion.
For example
●
Accelerator pedal position signal malfunction
●
TCM breakdown
●
Line pressure solenoid malfunction (shorting, sticking in ON state)
●
Pressure regulator valve or plug sticking
●
Pilot valve sticking or pilot filter clogged
The pressure rises,
but does not enter the
standard position.
Possible causes include malfunctions in the pressure supply system and malfunction in the
pressure adjustment function.
For example
●
Accelerator pedal position signal malfunction
●
Line pressure solenoid malfunction (sticking, filter clog)
●
Pressure regulator valve or plug sticking
●
Pilot valve sticking or pilot filter clogged
Only low for a specific
position
Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
AT-54
TROUBLE DIAGNOSIS
ROAD TEST
Description
●
The road test inspects overall performance of the A/T and analyzes possible malfunction causes.
●
The road test is carried out in the following three stages.
1.
Check before engine is started. Refer to
.
2.
Check at idle. Refer to
3.
Cruise test
–
Inspect all the items from Part 1 to Part 3. Refer to
,
,
.
●
Before beginning the road test, check the test procedure and inspection items.
●
Test all inspection items until the symptom is uncovered. Diagnose NG items when all road tests are com-
plete.
Check Before Engine is Started
NCS000BX
1.
CHECK A/T CHECK INDICATOR LAMP
1.
Park vehicle on level surface.
2.
Move selector lever to “P” position.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON. (Do not start engine.)
Does A/T CHECK indicator lamp light up for about 2 seconds?
YES
>> 1. Turn ignition switch OFF.
2. Perform self-diagnostics and record all NG items on the
AT-86, "SELF-DIAGNOSTIC RESULT MODE"
AT-95, "Diagnostic Procedure With-
NO
>> Stop the road test and go to
AT-181, "A/T CHECK Indicator Lamp Does Not Come On"
.
Check at Idle
NCS000BY
1.
CHECK STARTING THE ENGINE
1.
Park vehicle on level surface.
2.
Move selector lever to “P” or “N” position.
3.
Turn ignition switch OFF.
4.
Turn ignition switch to “START” position.
Does the engine start?
YES
>> GO TO 2.
NO
>> Stop the road test and go to
AT-181, "Engine Cannot Be Started in “P” or “N” Position"
2.
CHECK STARTING THE ENGINE
1.
Turn ignition switch ON. (Do not start engine.)
2.
Move selector lever to “D”, “M” or “R” position.
3.
Turn ignition switch to “START” position.
Does the engine start in either position?
YES
>> Stop the road test and go to
AT-181, "Engine Cannot Be Started in “P” or “N” Position"
NO
>> GO TO 3.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст