Infiniti G35 (V35). Manual — part 38
DTC P1754 INPUT CLUTCH SOLENOID VALVE FUNCTION
AT-143
D
E
F
G
H
I
J
K
L
M
A
B
AT
WITH GST
Follow the procedure “WITH CONSULT-II”.
Diagnostic Procedure
NCS000FF
1.
CHECK INPUT SIGNALS
With CONSULT-II
1.
Start engine.
2.
Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “A/T” with CONSULT-II.
3.
Drive vehicle in “D” position (3rd
Þ
4th gear), and confirm the
ON/OFF actuation of “ATF PRES SW 3” and electrical current
value of “I/C SOLENOID”.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
AT-172, "MAIN POWER SUPPLY AND GROUND CIR-
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace control valve with TCM. Refer to
AT-225, "Control Valve with TCM and A/T Fluid Temper-
.
NG
>> Repair or replace damaged parts.
4.
CHECK DTC
Perform
AT-142, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Item name
Condition
Display value
(Approx.)
I/C SOLENOID
Input clutch disengaged. Refer to
.
0.6 - 0.8 A
Input clutch engaged. Refer to
0 - 0.05 A
ATF PRES SW 3
Input clutch engaged. Refer to
.
ON
Input clutch disengaged. Refer to
.
OFF
SCIA4795E
AT-144
DTC P1757 FRONT BRAKE SOLENOID VALVE
DTC P1757 FRONT BRAKE SOLENOID VALVE
PFP:31940
Description
NCS000FG
Front brake solenoid valve is controlled by the TCM in response to signals sent from the PNP switch, vehicle
speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then be shifted to the
optimum position.
CONSULT-II Reference Value
NCS000FH
On Board Diagnosis Logic
NCS000FI
●
This is an OBD-II self-diagnostic item.
●
Diagnostic trouble code “P1757 FR/B SOLENOID/CIRC” with CONSULT-II or 6th judgment flicker without
CONSULT-II is detected under the following conditions.
–
When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
–
When TCM detects as irregular by comparing target value with monitor value.
Possible Cause
NCS000FJ
●
Harness or connectors.
(Solenoid circuit is open or shorted.)
●
Front brake solenoid valve.
DTC Confirmation Procedure
NCS000FK
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before preforming the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELECTION FROM MENU” in “DATA MONITOR” mode
for “A/T” with CONSULT-II and check monitor “ACCELE POSI”,
“SLCT LVR POSI” and “GEAR”.
3.
Touch “START”.
4.
Start engine.
5.
Drive vehicle and maintain the following conditions for at least 5
consecutive seconds.
ACCELE POSI: 1.5/8 - 2.0/8
SLCT LVR POSI: “D” position
GEAR: “3”
Þ
“4” (FR/B ON/OFF)
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
6.
AT-145, "Diagnostic Procedure"
WITH GST
Follow the procedure “WITH CONSULT-II”.
Item name
Condition
Display value (Approx.)
FR/B SOLENOID
Front brake engaged. Refer to
0.6 - 0.8 A
Front brake disengaged. Refer to
0 - 0.05 A
BCIA0031E
DTC P1757 FRONT BRAKE SOLENOID VALVE
AT-145
D
E
F
G
H
I
J
K
L
M
A
B
AT
Diagnostic Procedure
NCS000FL
1.
CHECK INPUT SIGNAL
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T”
with CONSULT-II.
3.
Start engine.
4.
Read out the value of “FR/B SOLENOID” while driving.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
AT-172, "MAIN POWER SUPPLY AND GROUND CIR-
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace control valve with TCM. Refer to
AT-225, "Control Valve with TCM and A/T Fluid Temper-
.
NG
>> Repair or replace damaged parts.
4.
CHECK DTC
Perform
AT-144, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Item name
Condition
Display value
(Approx.)
FR/B SOLENOID
0.6 - 0.8 A
Front brake disengaged. Refer to
.
0 - 0.05 A
SCIA4793E
AT-146
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION
DTC P1759 FRONT BRAKE SOLENOID VALVE FUNCTION
PFP:31940
Description
NCS000FM
●
Front brake solenoid valve is controlled by the TCM in response to signals sent from the PNP switch, vehi-
cle speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then be
shifted to the optimum position.
●
This is not only caused by electrical malfunction (circuits open or shorted) but also by mechanical mal-
function such as control valve sticking, improper solenoid valve operation.
CONSULT-II Reference Value
NCS000FN
On Board Diagnosis Logic
NCS000FO
●
This is an OBD-II self-diagnostic item.
●
Diagnostic trouble code “P1759 FR/B SOLENOID FNCT” with CONSULT-II or 6th judgment flicker without
CONSULT-II is detected under the following conditions.
–
When TCM detects that actual gear ratio is irregular, and relation between gear position and condition of
ATF pressure switch 1 is irregular during depressing accelerator pedal. (Other than during shift change)
–
When TCM detects that relation between gear position and condition of ATF pressure switch 1 is irregular
during releasing accelerator pedal. (Other than during shift change)
Possible Cause
NCS000FP
●
Harness or connectors.
(Solenoid and switch circuits are open or shorted.)
●
Front brake solenoid valve.
●
ATF pressure switch 1.
DTC Confirmation Procedure
NCS000FQ
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1.
Start engine.
2.
Accelerate vehicle to maintain the following conditions.
ACCELE POSI: 1.5/8 - 2.0/8
SLCT LVR POSI: “D” position
GEAR: “3”
Þ
“4” (FR/B ON/OFF)
Driving location: Driving the vehicle uphill (increased
engine load) will help maintain the driving conditions
required for this test.
3.
Perform step “2” again.
4.
Turn ignition switch OFF, then perform step “1” to “3” again.
5.
Check “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II. If DTC (P1759) is detected, refer to
AT-147, "Diagnostic Procedure"
If DTC (P1757) is detected, go to
AT-145, "Diagnostic Procedure"
If DTC (P1841) is detected, go to
AT-165, "Diagnostic Procedure"
Item name
Condition
Display value (Approx.)
FR/B SOLENOID
Front brake engaged. Refer to
0.6 - 0.8 A
Front brake disengaged. Refer to
0 - 0.05 A
ATF PRES SW 1
Front brake engaged. Refer to
.
ON
Front brake disengaged. Refer to
.
OFF
BCIA0031E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст