Infiniti G35 (V35). Manual — part 206
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-211
C
D
E
F
G
H
J
K
L
M
A
B
BL
3.
CHECK TRUNK LID LOCK ASSEMBLY (TRUNK ROOM LAMP SWITCH) GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between trunk lid lock assembly (trunk room
lamp switch) connector and ground.
OK or NG
OK
>> Check trunk kid lock assembly.
NG
>> Repair or replace trunk room lamp switch harness.
Diagnostic Procedure 2
NIS001J1
CHECK SECURITY INDICATOR LAMP
1.
SECURITY INDICATOR LAMP ACTIVE TEST
With CONSULT-II
Check “THEFT IND” in “ACTIVE TEST” mode with CONSULT-II.
OK or NG
OK
>> Security indicator lamp is OK.
NG
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect security indicator lamp connector.
3.
Check voltage between security indicator lamp connector M34
terminal 1 and ground.
OK or NG
OK
>> Check the following.
●
Harness for open or short between BCM and security
indicator lamp
●
Security indicator lamp condition
NG
>> Check the following.
●
10A fuse [No.19, located in fuse block (J/B)]
●
Harness for open or short between security indicator lamp and fuse
Terminal
Door switch
Continuity
Door switch
1
3
Pushed
No
Released
Yes
PIIB9119E
Perform operation shown on display indicator lamp
should illuminate.
PIIA7005E
1 – Ground
: Battery voltage
PIIA1128E
BL-212
VEHICLE SECURITY (THEFT WARNING) SYSTEM
Diagnostic Procedure 3
NIS001J2
CHECK FRONT DOOR KEY CYLINDER SWITCH
1.
CHECK KEY CYLINDER SWITCH OPERATION
Check if door key cylinder switch using key.
Do doors lock / unlock when using the key?
YES
>> Front door key cylinder switch operation is OK.
NO
>> Check door key cylinder switch circuit. Refer to
BL-212, "CHECK FRONT DOOR KEY CYLINDER
Diagnostic Procedure 4
NIS001J3
CHECK VEHICLE SECURITY HORN ALARM
First perform the “SELF-DIAG RESULTS” of “BCM” with CONSULT-II, then perform the trouble diagno-
sis of malfunction system indicated in “SELF-DIAG RESULTS” of “BCM”. Refer to
munication Inspection Using CONSULT-II (Self-Diagnosis)"
1.
CHECK HORN OPERATION
Check if horn sounds with horn switch.
Does horn operate?
Yes
>> GO TO 2.
No
>> GO TO 3.
2.
CHECK IPDM E/R INPUT SIGNAL
Check voltage between IPDM E/R connector E9 terminal 51 and ground.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> GO TO 3.
3.
CHECK HORN RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R and horn relay connector.
3.
Check continuity between IPDM E/R connector E9 terminal 51 and horn relay connector E20 terminal 1.
OK or NG
OK
>> Check harness connection.
NG
>> Repair or replace harness.
51 – Ground
: Battery voltage
PIIA9444E
51 – 1
: Continuity should exist.
PIIA9445E
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-213
C
D
E
F
G
H
J
K
L
M
A
B
BL
Diagnostic Procedure 5
NIS001J4
CHECK VEHICLE SECURITY HEADLAMP ALARM
1.
CHECK HEADLAMP OPERATION
Check if headlamp operate by lighting switch.
Does headlamp come on when turning switch “ON”?
YES
>> Headlamp circuit is OK.
NO
>> Check headlamp system. Refer to
LT-5, "HEADLAMP - XENON TYPE -"
or
.
Diagnostic Procedure 6
NIS001J5
CHECK DOOR LOCK AND UNLOCK SWITCH
1.
CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL
Check if power door lock operated by door lock and unlock switch.
Do doors lock / unlock when using each door lock and unlock switches?
YES
>> Door lock and unlock switch is OK.
NO
>> Check door lock and unlock switch. Refer to
BL-214
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
PFP:28591
Component Parts and Harness Connector Location
NIS001KK
PIIB4394E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст