Infiniti G35 (V35). Manual — part 507
EXHAUST SYSTEM
EX-3
C
D
E
F
G
H
I
J
K
L
M
A
EX
EXHAUST SYSTEM
PFP:20100
Checking Exhaust System
NBS00135
Check exhaust pipes, muffler and mounting for improper attachment,
leaks, cracks, damage or deterioration.
●
If anything is found, repair or replace damaged parts.
Removal and Installation
NBS00136
CAUTION:
●
Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
●
Perform the operation with the exhaust system fully cooled down because the system will be hot
just after engine stops.
●
Be careful not to cut your hand on the heated insulator edge.
SMA211A
1.
Mounting rubber
2.
Main muffler mounting bracket
3.
Main muffler
4.
Ring gasket
5.
Mounting bracket
6.
Center muffler
7.
Collar
8.
Grommet
9.
Exhaust mounting bracket
10. Gasket
11. Exhaust front tube
PBIC2037E
EX-4
EXHAUST SYSTEM
REMOVAL
●
Disconnect each joint and mounting with power tool.
●
When removing main muffler, remove main muffler mounting bracket bolts.
INSTALLATION
Note to the following, and install in the reverse order of removal.
●
Tighten main muffler mounting bracket bolts in numerical order
as shown in the figure.
When reassembling main muffler only.
1.
Temporarily tighten connecting flange (A).
2.
Move main muffler front/rear/left/right so that clearance between
tail tube and bumper is even.
3.
Tighten connecting flange (A) to the specified torque.
When reassembling center muffler.
1.
Temporarily tighten connecting flanges in order of (A) and (B).
2.
Move main muffler front/rear/left/right so that clearance between
tail tube and bumper is even.
3.
Tighten connecting flanges in order of (A) and (B) to the speci-
fied torque.
When reassembling exhaust front tube.
1.
Temporarily tighten connecting flanges of center muffler in order of (B) and (C).
2.
Move main muffler front/rear/left/right so that clearance between tail tube and bumper is even.
3.
Tighten connecting flanges in order of (B) and (C) to the specified torque.
CAUTION:
●
Always replace exhaust tube gaskets with new ones when reassembling.
●
If heated insulator is badly deformed, repair or replace it. If deposits such as mud pile up on
heated insulator, remove them.
●
When installing heated insulator avoid large gaps or interference between heated insulator and
each exhaust pipe.
●
Remove deposits from the sealing surface of each connection. Connect them securely to avoid
gas leakage.
●
Temporarily tighten mounting nuts on the exhaust manifold side and mounting bolts on the vehi-
cle side. Check each part for unusual interference, and then tighten them to the specified torque.
●
When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/
left directions.
INSPECTION AFTER INSTALLATION
●
With engine running, check exhaust tube joints for gas leakage and unusual noises.
●
Make sure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
●
Make sure that clearance between tail tube and bumper is even.
PBIC1675E
PBIC2104E
FAX-1
FRONT AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
A
B
FAX
FRONT AXLE
PREPARATION . . . . . . . . . . . . . . ... 2
Special Service Tools . . . . . . . . . . . ... 2
Commercial Service Tools . . . . . . . . . . 2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 3
NVH Troubleshooting Chart . . . . . . . . . . 3
FRONT WHEEL HUB AND KNUCKLE . . . . . .. 4
On-Vehicle Inspection . . . . . . . . . . . .. 4
WHEEL BEARING INSPECTION . . . . . . . 4
Removal and Installation . . . . . . . . . . .. 4
SERVICE DATA AND SPECIFICATIONS (SDS) . . 7
FAX-2
PREPARATION
PREPARATION
PFP:00002
Special Service Tools
NDS0001T
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
NDS0001U
Tool number
(Kent-Moore No.)
Tool name
Description
HT72520000
(J-25730-A)
Ball joint remover
a: 33 mm (1.30 in)
b: 50 mm (1.97 in)
r: 11.5 mm (0.453 in)
Removing steering outer socket
ST3127S000
(J-25765-A)
Preload gauge
Measuring rotating torque of ball joint
NT546
ZZA0806D
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст