Infiniti G35 (V35). Manual — part 400
DTC P0500 VSS
EC-481
C
D
E
F
G
H
I
J
K
L
M
A
EC
5.
Maintain the following conditions for at least 60 consecutive sec-
onds.
6.
If 1st trip DTC is detected, go to
EC-482, "Diagnostic Procedure"
ENG SPEED
1,600 - 6,000 rpm (A/T)
1,800 - 6,000 rpm (M/T)
COOLAN TEMP/S
More than 70
°
C (158
°
F)
B/FUEL SCHDL
5.3 - 31.8 msec (A/T)
5.0 - 31.8 msec (M/T)
Shift lever
Except P or N position (A/T)
Except Neutral position (M/T)
PW/ST SIGNAL
OFF
SEF196Y
EC-482
DTC P0500 VSS
Overall Function Check
NBS000UH
Use this procedure to check the overall function of the vehicle speed sensor circuit. During this check, a 1st
trip DTC might not be confirmed.
WITH GST
1.
Lift up drive wheels.
2.
Start engine.
3.
Read vehicle speed sensor signal in Service $01 with GST.
The vehicle speed sensor on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.
4.
If NG, go to
EC-482, "Diagnostic Procedure"
Diagnostic Procedure
NBS000UI
1.
CHECK DTC WITH VDC/TCS ABS CONTROL UNIT
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace.
2.
COMBINATION METER
Check combination meter function.
Refer to
.
>> INSPECTION END
DTC P0506 ISC SYSTEM
EC-483
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0506 ISC SYSTEM
PFP:23781
Description
NBS000UJ
NOTE:
If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan
operation, etc.).
On Board Diagnosis Logic
NBS000UK
DTC Confirmation Procedure
NBS000UL
NOTE:
●
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait
at least 10 seconds before conducting the next test.
●
If the target idle speed is out of the specified value, perform
EC-79, "Idle Air Volume Learning"
before conducting DTC Confirmation Procedure. For the target idle speed, refer to
VICE DATA AND SPECIFICATIONS (SDS)"
TESTING CONDITION:
●
Before performing the following procedure, confirm that battery voltage is more than 11V at idle.
●
Always perform the test at a temperature above
−
10
°
C (14
°
F).
WITH CONSULT-II
1.
Open engine hood.
2.
Start engine and warm it up to normal operating temperature.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON again and select “DATA MONITOR”
mode with CONSULT-II.
5.
Start engine and run it for at least 1 minute at idle speed.
6.
If 1st trip DTC is detected, go to
EC-484, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0506
0506
Idle speed control sys-
tem RPM lower than
expected
The idle speed is less than the target idle
speed by 100 rpm or more.
●
Electric throttle control actuator
●
Intake air leak
SEF174Y
EC-484
DTC P0506 ISC SYSTEM
Diagnostic Procedure
NBS000UM
1.
CHECK INTAKE AIR LEAK
1.
Start engine and let it idle.
2.
Listen for an intake air leak after the mass air flow sensor.
OK or NG
OK
>> GO TO 2.
NG
>> Discover air leak location and repair.
2.
REPLACE ECM
1.
Stop engine.
2.
Replace ECM.
3.
Perform initialization of IVIS (NATS) system and registration of all IVIS (NATS) ignition key IDs.
Refer to
BL-217, "ECM Re-Communicating Function"
.
4.
Perform
5.
Perform
EC-78, "Exhaust Valve Timing Control Learning (M/T models)"
.
6.
Perform
EC-79, "Accelerator Pedal Released Position Learning"
.
7.
Perform
EC-79, "Throttle Valve Closed Position Learning"
8.
Perform
EC-79, "Idle Air Volume Learning"
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст