Infiniti G35 (V35). Manual — part 632
MA-26
CHASSIS AND BODY MAINTENANCE
PAD
●
Check for wear or damage.
Checking Steering Gear and Linkage
NLS00022
STEERING GEAR
●
Check gear housing and boots for looseness, damage and
grease leakage.
●
Check connection with steering column for looseness.
STEERING LINKAGE
Check ball joint, dust cover and other component parts for looseness, wear, damage and grease leakage.
Checking Power Steering Fluid and Lines
NLS00023
Check fluid level in reservoir tank with engine off.
Use “HOT” range at fluid temperatures of 50 to 80
°
C (122 to 176
°
F)
or “COLD” range at fluid temperatures of 0 to 30
°
C (32 to 86
°
F).
CAUTION:
●
Do not overfill.
●
Recommended fluid is Genuine NISSAN PSF or equivalent.
Refer to
MA-10, "RECOMMENDED FLUIDS AND LUBRI-
BRA0010D
Front
Rear
Standard thickness
11.0 mm (0.433 in)
8.5 mm (0.335 in)
Repair limit thickness
2.0 mm (0.079 in)
2.0 mm (0.079 in)
SLIA0014E
SST850C
CHASSIS AND BODY MAINTENANCE
MA-27
C
D
E
F
G
H
I
J
K
M
A
B
MA
●
Check lines for improper attachment, leaks, cracks, dam-
age, loose connections, chafing and deterioration.
●
Check rack boots for accumulation of power steering fluid.
Axle and Suspension Parts
NLS00024
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.
●
Shake each wheel to check for excessive play.
●
Check wheel bearings for smooth operation.
●
Check axle and suspension nuts and bolts for looseness.
●
Check strut (shock absorber) for oil leakage or other damage.
●
Check suspension ball joint for grease leakage and ball joint
dust cover for cracks or other damage.
Lubricating Locks, Hinges and Hood Latch
NLS00025
SST851C
SMA525A
SFA392B
PIIA3615E
MA-28
CHASSIS AND BODY MAINTENANCE
Checking Seat Belt, Buckles, Retractors, Anchors and Adjusters
NLS0005P
CAUTION:
●
After any collision, inspect all seat belt assemblies, including retractors and other attached hard-
wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in
use during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improp-
erly operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal col-
lision where the driver and passenger air bags are deployed.
●
If any component of seat belt assembly is questionable, do not repair.
Replace as seat belt assembly.
●
If webbing is cut, frayed, or damaged, replace belt assembly.
●
Never oil tongue and buckle.
●
Use a genuine NISSAN seat belt assembly.
in SB section.
●
Check anchors for loose mounting
●
Check belts for damage
●
Check retractor for smooth operation
●
Check function of buckles and tongues when buckled and released
PIIB7156E
SERVICE DATA AND SPECIFICATIONS (SDS)
MA-29
C
D
E
F
G
H
I
J
K
M
A
B
MA
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Standard and Limit
NLS00027
BELT DEFLECTION AND TENSION
*: If belt tension gauge cannot be installed at check points shown, check drive belt tension at different location on the belt.
ENGINE COOLANT CAPACITY
Unit:
(US qt, lmp qt)
ENGINE OIL CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
SPARK PLUG (PLATINUM-TIPPED TYPE)
WHEEL BALANCE
Deflection adjustment
Unit: mm (in)
Tension adjustment*
Unit: N (kg, lb)
Used belt
New belt
Used belt
New belt
Limit
After adjustment
Limit
After adjustment
Alternator and
power steering
oil pump belt
7 (0.28)
4 - 5
(0.16 - 0.20)
3.5 - 4.5
(0.138 - 0.177)
294 (30, 66)
730 - 818
(74.5 - 83.5,
164 - 184)
838 - 926
(85.5 - 94.5,
188 - 208)
A/C compressor
belt
12 (0.47)
9 - 10
(0.35 - 0.39)
8 - 9
(0.31- 0.35)
196 (20, 44)
348 - 436
(35.5 - 44.5,
78 - 98)
470 - 559
(48 - 57,
106 - 126)
Applied pushing
force
98 (10, 22)
—
KBIA1731J
Engine coolant capacity (With reservoir tank at MAX level)
8.7 (9-1/4, 7-5/8)
Reservoir tank engine coolant capacity (At MAX level)
0.8 (7/8, 3/4)
Drain and refill
With oil filter change
4.7 (5, 4-1/8)
Without oil filter change
4.4 (4-5/8, 3-7/8)
Dry engine (Overhaul)
5.4 (5-3/4, 4-3/4)
Type
Standard
PLFR5A-11
Hot
PLFR4A-11
Cold
PLFR6A-11
Spark plug gap (Nominal)
1.1 mm (0.043 in)
Maximum allowable unbalance
Dynamic (At rim flange)
Less than 5 g (0.17 oz) (one side)
Static (At rim flange)
Less than 10 g (0.35 oz)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст