Infiniti G35 (V35). Manual — part 170
REMOTE KEYLESS ENTRY SYSTEM
BL-67
C
D
E
F
G
H
J
K
L
M
A
B
BL
2.
CHECK KEYFOB FUNCTION
With CONSULT-II
Check keyfob function in “DATA MONITOR” mode with CONSULT-II.
When pushing each button of keyfob, the corresponding monitor item should be turned as follows.
OK or NG
OK
>> Keyfob is OK.
NG
>> Replace keyfob.
Check ACC Power Supply
NIS000BW
1.
CHECK ACC SWITCH
With CONSULT-II
Check ACC switch (“ACC ON SW ”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check voltage between BCM connector and ground.
OK or NG
OK
>> ACC power supply is OK.
NG
>> Check the following.
●
10A fuse [No. 6, located in fuse block (J/B)]
●
Harness for open or short between BCM and fuse.
Condition
Monitor item
Pushing LOCK
KEYLESS LOCK
: ON
Pushing UNLOCK
KEYLESS UNLOCK
: ON
Keep pushing UNLOCK
RKE KEEP UNLK
: ON*
*: RKE KEEP UNLK turns to ON three
seconds after UNLOCK button keeps
pushing.
Pushing TRUNK
KEYLESS TRUNK
: ON
Pushing PANIC
KEYLESS PANIC
: ON
Pushing LOCK and UNLOCK at the
same time
RKE LCK-UNLCK
: ON
PIIA9920E
Monitor item
Condition
ACC ON SW
Ignition switch position is ACC or ON
: ON
Ignition switch position is OFF
: OFF
PIIA3367E
Item
Connector
Terminals
(Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
BCM
M1
11 (LG)
Ground
ACC or ON
Battery voltage
OFF
0
PIIA7002E
BL-68
REMOTE KEYLESS ENTRY SYSTEM
Check Door Switch
NIS000BX
1.
CHECK DOOR SWITCH INPUT SIGNAL
With CONSULT-II
Check door switches (“DOOR SW-DR ” and “DOOR SW-AS ”) in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check voltage between BCM connectors B4 (driver side), M1 (pas-
senger side) terminals 62, 12 and ground.
OK or NG
OK
>> Door switch circuit is OK.
NG
>> GO TO 2.
Monitor item
Condition
DOOR SW-DR
CLOSE
→
OPEN
: OFF
→
ON
DOOR SW-AS
PIIA2464E
PIIB7648E
Item
Connectors
Terminals (Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
Driver side door switch
B4
62 (Y)
Ground
CLOSE
Passenger side door switch
M1
12 (P)
OPEN
0
SKIB3419J
REMOTE KEYLESS ENTRY SYSTEM
BL-69
C
D
E
F
G
H
J
K
L
M
A
B
BL
2.
CHECK DOOR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door switch and BCM connector.
3.
Check continuity between door switch connector B17 (driver side), B410 (passenger side) terminals 1 and
BCM connector B4, M1 terminals 62, 12.
4.
Check continuity between door switch connector B17 (driver
side), B410 (passenger side) terminals 1 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK DOOR SWITCH
Check continuity between door switch B17 (driver side) or B410 (passenger side) terminal 1 and ground part
of door switch.
OK or NG
OK
>> GO TO 4.
NG
>> Replace door switch.
Driver side door
1 (G/B) – 62 (Y)
: Continuity should exist.
Passenger side door
1 (P) – 12 (P)
: Continuity should exist.
1 (G/B and P) – Ground
: Continuity should not exist.
PIIA9540E
Terminal
Door switch
Continuity
1
Ground part of door switch
Pushed (close)
No
Released (open)
Yes
PIIA3351E
BL-70
REMOTE KEYLESS ENTRY SYSTEM
4.
CHECK DOOR SWITCH INPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM connectors B4 (driver side), M1 (passenger side) terminals 62, 12 and
ground.
OK or NG
OK
>> Check harness connection.
NG
>> Replace BCM.
Check Key Switch
NIS000BY
1.
CHECK KEY SWITCH INPUT SIGNAL
With CONSULT-II
Check ignition key cylinder switch “KEY ON SW ” in “DATE MONI-
TOR” mode with CONSULT-II
●
When key is inserted in ignition key cylinder
●
When key is removed from ignition key cylinder
Without CONSULT-II
Check voltage between BCM connector and ground.
OK or NG
OK
>> Key switch circuit is OK.
NG
>> GO TO 2.
Item
Con-
nec-
tors
Terminals (Wire
color)
Condi-
tion
Voltage [V]
(Approx.)
(+)
(–)
Driver
side door
switch
B4
62
(Y)
Ground
CLOS
E
Passen-
ger side
door
switch
M1
12
(P)
OPEN
0
PIIB7648E
SKIB3419J
KEY ON SW
: ON
KEY ON SW
: OFF
PIIA6470E
Connector
Terminals (Wire color)
Condition
Voltage [V]
(Approx.)
(+)
(–)
M1
37 (B/P)
Ground
Key is inserted
Battery voltage
Key is removed
0
PIIA9541E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст